I just got my first PCP rifle the Avenger Bullpup a week ago, on sale for $299 from Pyramid, and am working on a budget build.
I went with the CVLIFE 6-24x50 for $50- Amazon Link
VEVOR Hand pump for $50 - Amazon Link (Wow so much more force needed to pump than expected. My kid that weighs a little over a hundred can jump and put their full weight on the pump without fully compressing it.) Depressurizing to tune made me sad. Especially when I had to do it a second time. (I have it set to 1800 now). I backed off more than a quarter turn the first time I went to adjust and had the regulator gauge side down when filling, so I did not see what I had done till I had hand filled to 4000 ....
Looking through the forums I found Buck Rails moderators, I am going to add to my wish list, for down the road. - Buck Rails Link
Any thoughts on Donny FL vs UNI adapter. I have not seen much info about Buck's UNI adapter for the avenger.
I have no experience with Bipods, but from what I have read and watched I see it is highly recommended that you get one for this gun. What features should I be looking at,. Below is my best guess:
Height around 6-9"
Picatinny Rail connection (bottom or side) does mlok work for side rails? One person recommended a bipod with mlok, but I don;t know if they swapped out their rails?
Is the 360 swivel and tilt nice to have or just extra weight?
Recommendations for DIY rear support for precision shooting?
I would love to get the Quick shot upgrade if it is still being made so I can move the lever forward and to the left hand side.. I see one for sale used on this site, but just joined so I can't PM anyone for until I am a member for at least 10 days.
I have seem pictures of Bullpups with a 3d printed support for the rail. Does anyone know if the 3d print file is available or is it custom order only?
Helpful 3D print Files I found while looking:
Magazines - 12 and 20 Round Magazine 3D print files
Moderator - Moderator 3D print files
Gauge Covers - Gauge Cover 3D print Files
Any Recommendations for a cheap case or bag that will fit the rifle with scope? My Plano single Rifle with scope case I have for my Gamo Swarm is too small for bullpup with scope.
Any other must haves? I am trying to keep total buy in under $500 for essentials, with scope and pump and gun I am currently at $420 which is the bare essentials.
I went with the CVLIFE 6-24x50 for $50- Amazon Link
VEVOR Hand pump for $50 - Amazon Link (Wow so much more force needed to pump than expected. My kid that weighs a little over a hundred can jump and put their full weight on the pump without fully compressing it.) Depressurizing to tune made me sad. Especially when I had to do it a second time. (I have it set to 1800 now). I backed off more than a quarter turn the first time I went to adjust and had the regulator gauge side down when filling, so I did not see what I had done till I had hand filled to 4000 ....
Looking through the forums I found Buck Rails moderators, I am going to add to my wish list, for down the road. - Buck Rails Link
Any thoughts on Donny FL vs UNI adapter. I have not seen much info about Buck's UNI adapter for the avenger.
I have no experience with Bipods, but from what I have read and watched I see it is highly recommended that you get one for this gun. What features should I be looking at,. Below is my best guess:
Height around 6-9"
Picatinny Rail connection (bottom or side) does mlok work for side rails? One person recommended a bipod with mlok, but I don;t know if they swapped out their rails?
Is the 360 swivel and tilt nice to have or just extra weight?
Recommendations for DIY rear support for precision shooting?
I would love to get the Quick shot upgrade if it is still being made so I can move the lever forward and to the left hand side.. I see one for sale used on this site, but just joined so I can't PM anyone for until I am a member for at least 10 days.
I have seem pictures of Bullpups with a 3d printed support for the rail. Does anyone know if the 3d print file is available or is it custom order only?
Helpful 3D print Files I found while looking:
Magazines - 12 and 20 Round Magazine 3D print files
Moderator - Moderator 3D print files
Gauge Covers - Gauge Cover 3D print Files
Any Recommendations for a cheap case or bag that will fit the rifle with scope? My Plano single Rifle with scope case I have for my Gamo Swarm is too small for bullpup with scope.
Any other must haves? I am trying to keep total buy in under $500 for essentials, with scope and pump and gun I am currently at $420 which is the bare essentials.
Last edited: