just ordered one from krale the reviues i watched say its like a dana storm riders barrle and action and air tank small tank i was woundering what size the shroude is to buy the correct end cap to be able say buy a donnly fl adapter to convert it to 1/2 20 i think the shroude size o/d is smaller on the t rex bull pup than like a p35
any one have any info on a snow peak t rex bull pup
- Thread starter gizmo1974
- Start date
Upvote 0
just order one for hatsan like flash qe and its the correct thread https://donnyfl.com/collections/adapters/products/hatsan-qe-1-2-x-20-unf-adapter
Upvote 0
I'll expand on what Gizmo said: search for "Hatsan QE 1/2 x 20 Adapter", they're all over the place on google.
Upvote 0
I just ordered this one for my 177 t rex bullpup I hope it fits
1/2″-20 UNF
1/2"-20 or 28 Thread Adapter for Hatsan QE/BullBoss QE | ReddotMate
1/2"-20 or 28 Thread Adapter for Hatsan QE/BullBoss QE Compatible with the following Hatsan airguns: Hatsan Gladius Hatsan Flash Wood QE Hatsan AirMax 
www.reddotmate.com
1/2"-20 or 28 Thread Adapter for Hatsan QE/BullBoss QE | ReddotMate
1/2"-20 or 28 Thread Adapter for Hatsan QE/BullBoss QE Compatible with the following Hatsan airguns: Hatsan Gladius Hatsan Flash Wood QE Hatsan AirMax
www.reddotmate.com Upvote 0
Hello. Bit of an update.
Adapter arrived. It fits perfectly. You can either fit it as it is with an o ring as there's a small gap as the thread is slightly too long or you can take out one of the baffle rings from the end and it fits flush. The reason I opted for the o ring is I wanted to keep the baffles in the correct place as much as possible plus I wasn't sure if it went all the way to the stainless ring inside. Not fired it yet but I'm pretty sure it should now do the job with a silencer. I better get shopping for one.
Adapter arrived. It fits perfectly. You can either fit it as it is with an o ring as there's a small gap as the thread is slightly too long or you can take out one of the baffle rings from the end and it fits flush. The reason I opted for the o ring is I wanted to keep the baffles in the correct place as much as possible plus I wasn't sure if it went all the way to the stainless ring inside. Not fired it yet but I'm pretty sure it should now do the job with a silencer. I better get shopping for one.
Upvote 0
It helps quite a bit. Still not as quiet as 12 fpe modded Notos but close and this is 2x the FPE.
Upvote 0
hi- have you had any past experience with this company? did not find much on them with google. thanksI just ordered this one for my 177 t rex bullpup I hope it fits
1/2″-20 UNF
1/2"-20 or 28 Thread Adapter for Hatsan QE/BullBoss QE | ReddotMate
1/2"-20 or 28 Thread Adapter for Hatsan QE/BullBoss QE Compatible with the following Hatsan airguns: Hatsan Gladius Hatsan Flash Wood QE Hatsan AirMax
Upvote 0
Hello no it was a bit of a gamble for me to order from them,but to be fair it arrived after about a week or so and it's perfect.
Id added a couple of pictures when it arrived.
https://www.airgunnation.com/thread...snow-peak-t-rex-bull-pup.1303219/post-2015841
Cheers
David.
Upvote 0
oops- missed that... I wondered if if was a legit website, but good to know, lots of bits there. thanks.
Upvote 0
No worries pal. Good luck with it. I'm yet to get a silencer for it but with it on its sill shooting straight.
Upvote 0
Id use their site on a PC, but ive ordered from that company twice, got stuff in a week or so. They do paypal on android weird, so use PC or desktop mode.
Upvote 0
I havent looked at it yet, just mindlessly threw on an oring and tossed it together, but the grub screws might need to be loosened and retightened to snug things up. The o-ring might create a gap.
Upvote 0
Not sure where I got my o ring from. Think I might of stolen it from my normal .22 T-rex spares but it fits like a glove. Can remove a baffle if needed but I recon the o ring is the way to go and leaves the rifle as much intact as possible and is a good snug fit. When you say grub screws do you mean the ones holding the original shroud on? I didn't even think of them to be honest
Upvote 0
Yes those grubs. the "stack" is pinched between the barrel * shaped thing halfway through shroud and the shroud endcap.
The grubs would let you fully seat the cap without oring Im pretty sure.
Whether or not it matters I dunno, but I added to my list of things to check.
Last edited:
Upvote 0
Nice one I'll have a look at that. I do remember undoing them once and made a right mess. Got it all back on in the end.
Upvote 0