Huben Any issues or problems with Huben gk1 please share your experience

[Kenjeepman]

Just realized one if my 2 GK1 spare parts bags has a few K1 orings in it. Couple small ones and a valve o ring.. go figure the o-ring ive been waiting for. Wolfiek said they were out of stock and i said i believe they both use the same 11.6x1.8 o ring. She replied with “i dont think so” ..
One in my bag and other from a K1 spare parts kit i grabbed.

 

[Ultralight]

Just realized one if my 2 GK1 spare parts bags has a few K1 orings in it. Couple small ones and a valve o ring.. go figure the o-ring ive been waiting for. Wolfiek said they were out of stock and i said i believe they both use the same 11.6x1.8 o ring. She replied with “i dont think so” ..
One in my bag and other from a K1 spare parts kit i grabbed.

View attachment 576571

Interesting, I don't have such an o-ring in the bags I've seen.

 

[hvacguy]

GK1 manual shows brass screw oring (#59) as 4.5x1mm (https://www.hubenairguns.shop/colle...en-spare-parts-for-gk1?variant=47416272224588).

I bought some from oringsandmore.com and they're WAY too big. I end up using a 2.5x1.5mm with sanded down OD to fit. Gun holds air now but the brass doesn't go in all the way because the oring is still a little big. Anyone else run into this?

 

[WobblyHand]

GK1 manual shows brass screw oring (#59) as 4.5x1mm (https://www.hubenairguns.shop/colle...en-spare-parts-for-gk1?variant=47416272224588).

I bought some from oringsandmore.com and they're WAY too big. I end up using a 2.5x1.5mm with sanded down OD to fit. Gun holds air now but the brass doesn't go in all the way because the oring is still a little big. Anyone else run into this?

There's different ways to measure o-rings. Some places use the OD, others the ID. Take the OEM and place it in the center of the 4.5x1. It seems like it will just fit. Can you confirm that? If you have calipers, or a mm scale, can you estimate the ID of the 4.5x1 o-ring? Is it oh, 4.5mm ID?

So what you need might be a 4.5mm OD, and 1mm CS o-ring, but you ordered a 4.5mm ID x 1mm o-ring. To convert to ID based, that would be
4.5mm OD - 2 o-ring thicknesses (1) = 4.5-2 = 2.5mm ID x 1mm.

The 2.5mm ID x 1.5 is too big, since it's OD is 2.5mm (ID) + 2 o-ring thicknesses (1.5) = 2.5 + 2x1.5 = 5.5mm.

Based on this, I'd say you need to find/buy 2.5mm ID x 1mm o-rings.
Here's a link for some. https://www.oringsandmore.com/fkm-o-ring-2-5-x-1mm-minimum-25-pcs/

 

[hvacguy]

Yoire

There's different ways to measure o-rings. Some places use the OD, others the ID. Take the OEM and place it in the center of the 4.5x1. It seems like it will just fit. Can you confirm that? If you have calipers, or a mm scale, can you estimate the ID of the 4.5x1 o-ring? Is it oh, 4.5mm ID?

So what you need might be a 4.5mm OD, and 1mm ID o-ring, but you ordered a 4.5mm ID x 1mm o-ring. To convert to ID based, that would be
4.5mm OD - 2 o-ring thicknesses (1) = 4.5-2 = 2.5mm ID x 1mm.

The 2.5mm ID x 1.5 is too big, since it's OD is 2.5mm (ID) + 2 o-ring thicknesses (1.5) = 2.5 + 2x1.5 = 5.5mm.

Based on some this, I'd say you need to find/buy 2.5mm ID x 1mm o-rings.
Here's a link for some. https://www.oringsandmore.com/fkm-o-ring-2-5-x-1mm-minimum-25-pcs/

You’re right on the money. Old oring is chewed up but would fit perfectly when new. I forgot china uses OD instead of ID. Same issue with Notos/PP750 orings.

 

[Ultralight]

Where do you get your O-rings for the GK1s in the USA from Oring suppliers? Probably will buy a few dozen just in case..

 

[WobblyHand]

Where do you get your O-rings for the GK1s in the USA from Oring suppliers? Probably will buy a few dozen just in case..

It depends. If I need a bunch of o-rings I'll use the oringstore, or captainoring. Make sure you get a kit, if available, or ensure that you are ordering the correct size! Sometimes I sneak in an item, if I'm ordering from McMaster-Car. Ordering from McMaster means you are getting a bag of 100, so that's practical only for small o-rings, since they're cheap. It's rare to find one place that has what you need.

Another source is from the person who sells the GK1. I'd email Kelly at KrazCool and see if he sells a complete kit. If he doesn't have it, I'd bet he knows where to find them.

One note, the GK1 seems to use NBR80 o-rings in a few places. NBR80 is uncommon. The standard in the US is NBR70 (soft) and NBR90 (hard). Use NBR90 where there's direct contact to the high pressure air, if you can. The NBR70 can extrude and fail.

 

[kkarmical]

Where do you get your O-rings for the GK1s in the USA from Oring suppliers? Probably will buy a few dozen just in case..

Does anyone have a complete o-ring list? About to take this thing apart fix the slow leak, need to order up o-rings just in case some need to be replaced.

The O-Ring Store LLC, We make getting O-Rings easy!

O-Rings Online or B2B Sales Professionals—208.413.6377 via our new AI phone attendant! Millions of high-quality AS568 and Metric O-Rings, hydraulic seals, and custom Vulcanized O-Rings. ISO9001:2015 certified, we offer fast, reliable service and unmatched expertise. Shop now at The O-Ring Store...

www.theoringstore.com

Been using them for years now..

 

[Ultralight]

About to take this thing apart fix the slow leak, need to order up o-rings just in case some need to be replaced.

DId you use the brass screw under the loading gate to degas? If so, that is likely your slow leak and a good place to start. Super easy.

 

[Ultralight]

Would be great to get a list of O-rings that are most commonly worn out and the rough frequency they are replaced.

Also, if anyone here knows if any sections/parts should be opened up for regular lubrication.

 

[Ezana4CE]

Does anyone have a complete o-ring list? About to take this thing apart fix the slow leak, need to order up o-rings just in case some need to be replaced.

The O-Ring Store LLC, We make getting O-Rings easy!

O-Rings Online or B2B Sales Professionals—208.413.6377 via our new AI phone attendant! Millions of high-quality AS568 and Metric O-Rings, hydraulic seals, and custom Vulcanized O-Rings. ISO9001:2015 certified, we offer fast, reliable service and unmatched expertise. Shop now at The O-Ring Store...

www.theoringstore.com

Been using them for years now..

Would be great to get a list of O-rings that are most commonly worn out and the rough frequency they are replaced.

Also, if anyone here knows if any sections/parts should be opened up for regular lubrication.

I’m assuming that these are all of the o-rings needed. Check pages 11-18 in the owner’s manual. If these are all of necessary o-rings then it would only take someone about 20-30 minutes to sift through them and compile the listed sizes into a an exclusive o-ring list.

https://www.hubenairguns.com/download/GK1%20Manual%20-%20English.pdf