Search results for query: *

Ok I will measure the original reg and see what size it is. I fitted the original fx reg and everything works fine so I’m starting to think he might need a gen 2 huma reg now. Thanks for the help. regards, James

 

He was told by huma that he needs the gen3 reg for the mk2 crown and the diagram on huma’s page shows all the same washers on the gen3 extra high pressure version of their reg so you don’t have different thicknesses on his particular one. The only thing I can think of is that the gen3 reg isn’t...

My friend has a mk2 crown in .25 and needs to know how the washers stack on the piston. I’ve looked all over but I’m not 100% sure so can anyone help me please? he ordered the extra high pressure huma reg but when he opens the reg past 100 bar no air come out like it’s out of air so he wants to...

 

I’ve noticed though that every slug liner kit comes with other parts to give to more power when using slugs. You can buy a .35 slug liner now. They have them in stock here in the uk so I think I’ll order one. I’ll try 880fps and see what it’s like for accuracy. ive not fired the rifle yet so...

Hi everyone, ive just bought a .35 sniper edition Impact and was wondering what FPS you are with 81 grain pellets? I have searched and found someone say 860 and another say 915. this is my 3rd impact and I wanted to check what it’s doing and then tune it straight away. I am looking at...

Thanks weatherby, ok so I have some news from fx. They are telling me I have the wrong valve pin and need a different one to allow the rifle to go above 100 bar so it hopefully sounds like I’m getting somewhere. Can anybody get the parts below below for me and send to the uk if I pay through...

A24 is not related just to the impact x but Oscar at fx told me I needed the shorter ones for full power. He said the longer adaptotors are for sub12 ftlb only and that the full power versions use shorter adaptors. I’m only going off what he said but they are a lot shorter on the full power...

A24 x2 brass adaptors are the parts I’m refering too. The sub 12 has longer adaptors. I have noticed my valve rod has a derlin washer and a brass spacer at the seat area which is different to my old Impact. The old one only had a nylon spacer. Most of the rifle is the same but there are small...

Not that I know of. Oscar at fx Airguns never mentioned that it was different when he gave me the list unless they changed the valve seat in the impact x? And yes yes I changed the hammer spring to the fac one from my other Impact. Thanks for the reply’s guys ??

Ok so since I’m using the .30 barrel it comesin fac only so that’s definatly ok. I have changed the two brass rods the make a bigger air pocket in the housing. The hammer spring. The Belleville washers and the valve adjuster. I had a spare valve rod but when I compared the length with the one...

Hi mate, the breech seal is there. The power is on max and I had the valve screwed all the way in nearly. I just can’t understand what’s causing it to not work at anything over 110bar. It was a sub 12ftlbs rifle coverted but I put all the parts in from my other fac Impact and got the fac...

Also isn’t there meant to be something between the brass part? If anyone has any pics of there impact x valve rod to compare that would be greatthanks

I tried this setup on my Impact x but there was no power at all above 60 bar. It wasn’t even firing the pellet out the barrel and I was getting a slight air noise at the back of the rifle near the magazine area. I’ve changed beck to to 16 Belleville washer setup and the same is happening with...

Ok thanks mate, I do t have a problem with it but I have the 700mm .30 Impact x and I have some parts from the older gem and just wanted to know if it was the same. I will have a read up on the link you gave me and try that configuration of the Belleville washers. Cheers everyone for the help

Hi Michael, thanks for the reply. Ok but my reg piston is 2mm longer this tim in the X model. Can you confirm if this is true? I have not took it out yet but I was told they are and have a different Belleville washer setup this time. Thanks James

The impact valve rod is 13 1/4” so I’m wondering is the Impact x is the same length. 

Hey everyone, have anyone got a picture of the impact x valve rod? I was wondering if it’s the same as length as valve rod in the older Impact. If anyone knows that would be great. Thanks James 

Cheers mate ????