Search results for query: *

Had mine for a while (3months). I’m surprised that there seems to be no reviews or recent forum talking about this gun. Is it because at least in Finland it’s very hard to get. If ordered now delivery time is like 5 months. Is it the same everywhere? Is Hatsan not able to keep up with the...

That's no problem. Instead of cocking lever, let's use a winch :ROFLMAO:

So i got 1017fps with 46gr slug. Reg pressure about 220bar. That equals 105fpe. So the power level is almost there BUT the reg wont get a fill after shots! Reg pressure decreases shot after shot. I didn’t have time anymore to find out if it starts to take filling again. Maybe at 150bar it...

I don’t know what happened but when i started to fill the gun with reg adjust wheel set to max, the reg pressure slowly went up to about 200 bar as the compressor filled the gun. Now im getting decent power, a bit over 100fpe. One thing wonders me. When having hammer closed. The gun wont keep...

Can i get the regulator out easily from the gun so i could check mine? Do i have to remove whole plenum or can i get just regulator out?

Thanks for the info. So I might have a faulty regulator somehow. Any ideas how to get it to go further or should i contact the seller? I’m not afraid to tinker as long i dont break or alter anything.

I have slugs in 46g. They are not any better than a light pellet powerwise.

Well actually they didn’t lie about that 1800fps. Find a pellet light enough and it will happen. Talking about fps has always annoid me because what matters is the energy not the speed that can be whatever depenging on what pellet to shoot.

I don’t understandt how jsb heavy 33.95gr can still get same fpe that 46gr slugs i allready tried. Seems it’s not about the pellet since i have shot For example H&N heavy slugs 46gr 915fps. Jsb heavy 33,95gr 1060fps. Also i ”calibrated” my chrono by shooting my hw97k and pro sport over it and...

How do I adjust to 200bar when i have maxed out the reg adjuster allready?

When maxing out the regulator adjustment screw, regulator takes in 150 bar. In some forums, i have seen bigger numbers in this gun's regulator pressures but i don't no if they are correct or if the were bigger calibers. So what would be the steps to go trough when i want to make sure everything...

Hatsan has a reputation of reaching or exceeding their claimed energy numbers. I had numerous hatsans and same case with every one. This factor sniper L should put out 115fpe in 25. I’m getting only 85fpe and i have tried many different pellets. Reg pressure about 150 bar and hammer adjustment...

Can anyone suggest a spring that would suite better for this power level?

I cant find a plateu point for my hatsan factor sniper l. Im trying to make a low end tune. About 35fpe. Reg pressure about 75bar. Problem is that in those low reg pressures the spring hammer wont add speed even when i start from the loose end spring tension. Do i have too strong spring?

Copying my own writing from another air gun forum: Just got mine yesterday. Factor Sniper L .25. After playing it for a few hours I am very pleased at this point with the gun. I have owned a FX impact a few years ago so i have a good but pricewise unfair product to compare by memory. A few...

I went from springers to pcp’s and now back to only springers. And with pcp’s i went the route to the top notch guns. For example the fx impact. That is very nice and fascinating gun in all of it’s technical stuff but it got boring to me. To me springers makes every shot ”count” because the...

Same here, absolutely no gas rams for me anymore. Im wondering what perecentages of break barrels is hatsan manufacturing with gas rams vs springs. How can it be good business to have so much warranty claims and expences to hatsan with vortex’s failing so often.

I just did a conversion to 125 from vortex to spring. I may got lucky with the spring guide fit and it shoot’s like a dream. I cannot tell difference to a gas ram except for cocking. And cocking (or returning barrel) got better when deburring the piston / cocking arm slide surface. Also did...

I was able to assembly a full power hw97k just by hand but it surely resisted and wasn’t easy. The screw end cap is more difficult than troughpins for sure. My 97k was twangy before a good cleaning and good lube job. I was amazed how the twang went away with using lubro teknik sg3 grease...

Hello! Couldn't find an answer anywhere with google so im asking here: I have a Hatsan MOD 125 Sniper Vortex 22 cal that I want to convert from gas ram to spring. Since it's difficult to find the parts for the conversion, I bought the standard MOD 125 spring model .177 caliber. The idea to...