Search results for query: *

Are all the transfer ports from early 80's up to present date the the same part and interchangeable? The part number is almost the same but an a is added to current part #. 1322 026 vs 1322a026.

I have a Benjamin 132 that is underpowered. I was thinking about getting a seal kit but noticed air was leaking where the pump tube is inserted into the upper receiver. Is this something a seal kit will cure or is the brazing where tube enters receiver shot? I haven't disassembled gun to see...

Will increasing the ID of the transfer port on a current production Crosman 1322 have any noticeable increase in FPS if no other mods are done? If so how much? Current models are rated at 460 FPS.

You must have a more economical internet than mine. Neither place mentioned have the drifter at $100.

Crosman lists the 1322 at 460 fps and the drifter at 550 fps. Crosman tech rep says air valve and transfer port are the same . Is it reasonable to believe that 4.5" of extra barrel will produce 90 FPS more in the Drifter?

Ok, but is the build quality any good? I have 2 1377's from 1982 and 1991. Does the craftsmanship compare favorably? No local stores have The Drifter to check one out. Anyone know how much extra velocity comes with the extr 4 inches of barrel. I have seen reviews on the Amazon Crosman store...

Any opinions on the quality of the current Crosman " The Drifter " kits. Opinions from buyers on Amazon show a lot of low opinions on the current quality. Some say a lot of slop and flex in the pump linkage. Are the 1322's better in this respect? Interested due to the longer barrel. All input...

Thanks for the quick reply.

Who sells just the pump cups for these guns. I have found several full kits with o rings and seals. I tried Crosmsn website with no luck. I have a couple of them one from 82 and one from 92.

Barra finally sent out a RMA to return rifle and I received a new one that feeds pellets without binding in the magazine. When I registered it they told me to write an honest review and get a tin of pellets. I wrote an honest review of my experience and they said it didn't meet there...

Just got replacement magazines today. Same issue, this time the bolt would bind before the pellet cleared the magazine. I got the bolt retracted but now the pellet is partially in the magazine and in the barrel and now I can't remove the magazine. The problem must be an out of spec rifle. Now...

Can the rifle assembly be lifted out of the stock by removing the on screw in the forearm? How does the crossbolt safty come into play when removing the action?

The plunger tip of the bolt measures 260". A .260" drill bit will fit through the magazine front to rear. I believe it is a misalignment issue with the magazine. When the bolt is ran forward until it binds the magazine gets locks into place and there is zero movement of the magazine. There...

I found that if you adjust to much first stage pull out of the trigger you can't engage the safety. I don't understand why they ship the gun with so many O-Rings but no schematic of assembly. With Trigger adjusted to 1 pound very nice short trigger pull but no safety. Had to go back to a long...

Trigger isn't problem for me. It just needs to load from magazine and have the bolt operate correctly.

I know there is a screw holding the magazine together. I would be more confident taking it apart if there were some reassembly instructions. Things with springs can be tricky to reassemble if they just go spring on disassembly. BARRA STILL HASN'T RESPONDED TO MY INQUIRY!! Very poor customer...

Does your magazine have any wiggle room or movement when you load a pellet. Once my bolt binds up, the magazine is rock solid and zero movement.

Does anyone know how to disassemble/reassemble the 250Z magazines? My magazines are binding the bolt and it looks like the exit hole may need to be honed out a few thousandths to function. Right now I can't load and fire my rifle using the magazines. The bolts binds up at around 3/8" shy of...

I just got a 25 cal 250Z . The bolt binds up using both the magazines. It will allow bolt to push pellet into barrel but can't push bolt all the way in so I can drop handle and shoot. It binds so bad I have to wrap a rope around the bolt handle close to the bolt body and forcefully yank on...