Search results for query: *

2 main things: I used an 888 valve. Modded the CO2 adapter by adding a check valve and O-ring groove. Reinforced the frame.

I know - not exactly exotic looking - but then NOT SSP either since 2 stroke mod. 1 pump is std 853 performance. 2 pumps will get another 100fps and up to 7fpe. Or the same as a stock 880 or 760 MSP.

I‘m not sure of it’s history but it has been well cared for and has been registered on UJ’s site prior to me.

I was eyeballing that one but am still recovering from my first Supergrade purchase back in February. Our serial numbers are super close.

Well said. I‘ve had the 717 and 747, both could out shoot me and I only have one currently, a nice boxed 777 that I don’t shoot much. I have a V10 and like it a lot but drool every time I see a FAS. Maybe one day. Have had this Walther LP3 for a bit and finally got around to resealing it...

Just my opinion - every Sheridan Model C, no matter its age, should have 1.

2nd that. DAQ breechs came in both right and left side bolt configuration + set screw or threaded barrel retention methods.

I went with an Altaros external regulator set for 12fpe. Waiting for winter to loosen its grip to get outside. Shot at 30ft in my basement recently. Doesn’t seem be pellet picky 👍

Received a full refund due to damage during transit. Stock repair came out good and spent the refunded $’s on a regulator, optics and other goodies. 👍

Here’s a photo of my 1955 (top) and 1950 Silver Streaks. Followed by front site differences 1950 is undercut vs later straight. Next up rear site chances late 50’s on top, 55 middle, 1950 bottom (Note: hand guard was not introduced ‘till the 60’s) Breach differences. The bolt pin hole was...

I received my PP700W a couple weeks ago. https://www.balistas.com/air-pistol-spa-pp700w-45mm?_gl=1*1fm916o*_up*MQ..*_ga*ODk0MTk0NzIxLjE3MzkxODMzODc.*_ga_R88M28QYBV*MTczOTE4MzM4Ny4xLjAuMTczOTE4MzM4Ny4wLjAuMA.. Factory set rite at 10fpe and seems to be a good one. So far reg is very stable.

RickH I too can relate to an interest in 10M Comp pistols. Not seriously, but I like to hit what I am aiming at. I’ve had a few Daisy 7x7‘s and still have a triple 7 but don’t shoot it often as my V10. I did a little work on the grip to make it more comfortable and though is a pain to load...

the 50’s streaks are my favorite. I have 4 now - 2 silvers and 2 blues. I never picked up for that pice though. You did well!

In the photo the .177 105s are on the left & the .22 106s are on the right. The bottom right 106 had a broken loop handle. I thought the 1300 lever looked better than a 130 lever

Initially threw this together back in early December, just after getting laid off for the winter season. It balances nice in the hand but was top heavy with the dot site I initially mounted. Inspiration hit last nite and this morning I found the open sites in the parts basket. Drilled and tapped...

I’d be more inclined to think that any leak during the shot cycle would be coming from the barrel o-ring or transfer port seal. Try laying a tissue over the loading area (no clip) and dry fire your PRod. If the tissue lifts off the receiver I’d replace the barrel O-ring, if it just kind of...

Atleast with the alcohol flush attempt, if it needs rebuild it will already be cleaned inside 👍

Notes on my ‘66 Benji 132 after reseal - 8 pumps max … std 14gr pellets = 350fps, Hobbies = 400fps

My vintage Benjamin and Crosman MSP pistols shoot these well at 30’ in my basement