Search results for query: *

Last time I replaced the probe O rings it didn't have any positive effect. I replaced the reg O ring near the delrin seal and it reduced creep. For routine maintenance I'd like to replace the larger O ring in the body of the reg, but I can't get the damn cap off. I don't know if this will fix...

Looks in good condition. For routine maintenance I apply a little silicon oil.

Not offended. I have always degassed the the gun and fired 3 or 4 dry fires after the degas.

Thanks for the reply. I'm working with original (non-x) regulator. I tried 3 different snap ring pliers and can't get the cap off! Dogowsky said heat from a torch will work, I tried that. Per your replay, may be I'll try an Avenge X regulator.

Short answer- I ordered (2) Caption O'ring kits. Part # change?? A while ago I downloaded a schematic (I think from Air Venturi, see attached), smaller o'ring: 000p2-072-x-00, larger o'ring: 000p2-073-x-00. I think pyramid has different part #s, and updated part list. Before there were no...

Thanks for the response and the tip on the oring store. I tried pyramid but I'll go back an try again. On the phone on a different question the were not much help, so I may contact you. I have one damaged reg so I will try more heat on that.

If you have it handy can you specify what part # or dimension you ordered from the oring store? The closest I could find was 3/32 - 1/16 ?? I have 3 avengers, (2) .22s and (1) .177. I need work on the regulators. Captain Oring only has 1 oring near the delrin seal. On 1 .22 I buffed out the...

How do you get the skill, thought this forum was for that. My bad.

Sorry, senior moment, Avenger both a .177 and a .22.

Question ?? I'd like to check/replace the O-rings under a new regulator. How do you get the belleville washers out so you can check the O-rings. Don't want to force them out (unless necessary), & do damage. I'm a newbie.

IN

nervoustrig A hint or logic? If I remove the barrel, and check/replace ps-011-x-00 O-rings (H in Captain O-rings kit), does this correspond to "barrel port" in the diagram you sent? If so I'll do that. I bought a second reg kit to replace in my .177. I'd like to check the O-rings under the reg...

Back yard shooting. Fired 4-5 shots at each 5 yard interval. Don't know how to expand png. Hope it comes out.

per diagram Is the valve spring the O-rings/bellevilles under the reg. Only reason I ask I couldn't lube them as I couldn't remove the belleville washers when I replaced the reg. Did you read the exel files. If so I'll send back yard shooting data tomorrow. Speech class tomorrow.

Don't know if you can read exel files but if you can. Otherwise I'll try some thing else before I send backyard shooting data. Hopefully I answered the bolt probe question. Like to know more about the "barrel port is misaligned to the valve’s exhaust port". Stroke affected speech & writing...

Shooting today, have to wait til temp is > 40F in St.Louis or I'm too cold. Army gave me a gift of a blizzard and ice storm. I have the Chony set up in my basement. I'm unclear, made the reg and hammer spring mods on the .22 so far. Did Replace the bold O-rings on the .22 and silicon oiled. Shot...

Different times, .177 6 months ago, the .22 the end October. Using a gxPump cs2. Proper controls in place. Good though though. Don't think its the reg O rings?

Tying to I.D. a loss of power in both a .177 and .22 Avenger. Both a .177 & .22 operated correctly for 6-9 months, then the loss of power in both guns. Spent 4 months sending the .177 back to Air Venturi multiple times. No joy! I first measure efficiency with a chrono. I measure mutiple reg...

Tying to I.D. a loss of power in both a .177 and .22 Avenger. Both a .177 & .22 operated correctly for 6-9 months, then the loss of power in both guns. Spent 4 months sending the .177 back to Air Venturi multiple times. No joy! I first measure efficiency with a chrono. I measure mutiple reg...

How do you get the Belleville washers and O rings out for servicing. Looks like you need to force them. Didn't want to without more info. Virgin at taking the gun apart. Trying to tract down a loss of power. Spent 4 months sending the gun back to Air Venturi multiple times. No joy! Both a .177 &...