Search results for query: *

This listing has been renewed

Check your breech seal .. something is not producing constant firing sequence. Piston seal can effect that to if its tight. 1 use thin Kleenex warped over breech and fire. If it’s leaking It will tear. if unsure. 2 shaving Cream will guarantee to show a seal leak. .. self explanatory.

Thats a .905 27 coil set up. Easy - ire cocking for the power you get.. it’s a good kit. I saw 770 with a 14.66 solid thunk. You can get more from a R1 but why. .. it’s inn the zone.

Has no effect onnthe sears and was NOT used onnthe earlier units

Front T8 screw to tight back off as Lewis said. Most people have zero clue how a REKORD works sadly. if not the return spring needs replacing under the aluminum rear screw.

Is it the New .905 27 coil one or the .860 spring. Use a new Vac seal. They are sized well for R1 and will shoot in fast. Make sure to lightly ease the bottom outside rails of the shoe before install, a tiny file works to micro flatten them ALSO YOU WILL PROBABLY NEED TO RELIEVE A TINE BIT...

This is true ,but the HO KIT IS SUPPOSED TO give you a bump. It’s a R7. I get it. I’m not disparaging it as the R7 mob will be out in full force telling us all that they have killed a bear at 70 yards and it’s shot placement .. but rather 500 fps is the area of not dropping off at 25 yards...

ARH. COPIED Venom also. At one time they worked on some Joint projects.

Agreed. But it’s a R7. You don’t want to beat the pellet to the target while checking .. 😂 That being said , power with out a racy is a faster miss When I was building big guns for people they insisted this amount of power .. I said WHY? down range 750fps is all you need to 40 yards with...

Nope it’s a los of tiny volume.. albeit tiny it’s not the loss issue. it’s the seal sizing. They are designed to fit snugger and burn in. It’s a manufacture % game as every tube is different and if thats Built in leeway. That and they have no sharp edges to grab threads and holes for The...

Love the implosion .. 👍

Sizing Vac seals is tricky as the material is odd and Tom puts a small leading edge of them ( something I’ve never been a fan of ) size them from the face for better results. Without a lathe it’s a tough job. Can it be done ,Yes .. some had worth with a flat surface and 180aluminum oxide...

No , my tube was actually on the larger side of 25 mm .. That being said Tom changes the kits so often that the spring you have may not be the same. Coil count and such Like I said, they have such a short stroke and small tube you need to make sure to get all you can out of them. Snug is...

It may get 10 fps. But it sure is hell is not gonna get 70. If the seals snug. Was the Vac seal snug? It needs to be on the fine line to get the most of the tiny 25 mm short stroke.

I’ve got a R-7 .20 with a Vortek pg4 and it’s a hammer. Seal sizing is key with them as well as lube removal in the inner springs. That being said it is a tad snappy , there is immediate pre load at barrel break when loading. 550 fps with 11.4 Ftt.

Brass bushing is fine. The whole floating front half moon was a poor design they added fire wards WHY .. ITS USELESS BEDROCK BOB HAS BROKEN MORE OF THEM THANN ANY ONE. THE original QUatros never had them and were on their biggest guns. It’s not a sear point ,but rather a trigger blade rest

Spring is not needed.

That’s a original Quatro. The pin is 5 mm iirc. It’s the same diameter as the broken piece you have. You need it to be C clipped in or you makea inner metal bushing that fits the smaller pin you have. it’s a great trigger that can be really predictable with a few mods. Both screws can be...

It’s a common known issue , no one has had it happen more than Bedrock Bob. He shoots 3000 a week, from many Hatsans. He has had them all break. It’s a part that’s not needed if you know the original Quatro design with a bushing.. That being said I have a complete HATSAN Trigger unit laying...

This listing has been renewed