Search results for query: *

Thank you for your input. I did a quick test at 135 bar. 2 shots were 967 & 964 fps. I’ll test tomorrow when I have time. Thank you! Also, let me know when you finish sorting it out. I’ll test NSA slugs 33.5 & 34.9gr at this bar aswell

@jasmlowe .. correct. We’re talking about the same one…

The screw is just lose enough at setting 23 to wiggle the knob…. That’s maxed at correct? Any tighter and the knob won’t turn at all

.25 Crown MKII….600 mm slug liner with barrel swapped to slug port. Hammer spring max… 170 bar regulator… it’ll BARELY push 26gr hybrid 850fps… I started with 36gr NSA and it was 780-805fps… I see people shooting mid 900’s. What am I missing?

Recently bought a heavy liner (600mm) and shooting hybrid 26gr. I was shooting 950ish fps on the pellet port. Turned the fx barrel 180* to slug port and velocity dropped to 850-900 fps and shooting 12” high off my zero. What are y’all pushing fps on the slug port and why am I so inconsistent? I...

I have a kratos .25 and a crown MKII is .25 so I want the .22 Impact M3

Looking for input from the left handers…. I’d really like an FX Impact but not sure if left handed shooters can use it due to the mag sticking out on the right side. I’ve never seen an impact in person, just on YouTube.

You’re right, 3” is Al title over the top but it’s over 2” from furthest point to point on slugs. I fixed the harmonics today with slugs using fx chrono and an excel chart. I was a little surprised when I only backed off max hammer 6 turns. Any more and the exact 25,39 GR spears out. I bought...

How are you guys swapping from slugs to pellets or vise versa in the 600mm barrel? I bought the crown from Utahairguns and it was set at 150 bar regulator. Didn’t like the grouping. Ended up turning the down to 140 and 4 1/4 turns off max hammer. Shooting dime size pellets (25.39gr) at 30...

I finally found the correct orings. I’ve been shooting JSB 25 GR pellets out of it (60 or so) so far so good. I think it had something to do with the EBay barrel band I have on it. Maybe it was putting pressure on the back Oring by not keeping the barrel true

I also thought about buying and FX but I shoot left handed. And some are bullpups. I’m doing research now to see which ones are proven and which ones aren’t 

I did some testing today with a Caldwell chrono. It’s touchy. Didn’t ready a lot. This is on a rest at 26 yards

Good Morning all, I’m new to the PCP world and was curious to see what you guys knew about aftermarket barrels. The stock barrel on my Kratos doesn’t like slugs (previous post about blowing orings at transfer port). What companies make barrels that have been proven accuracy with slugs (length...

I’ve shot over 500 pellets through it. Line shouldn’t still be in there correct? I put a new vortex 4x12 on it. The springer is rough on scopes. Destroyed the cheap gamo it came with. 

I just tested an hour ago. It’s been mid 60’s in the morning here in south florida

I noticed my springer will shoot about 6 inch low (first shot of the day) but each shot after will be higher and higher. usually by the 4-5 shot it will back on center again. I've been testing this for the past week. same results. I'm assuming because the barrel gets warm by then. I'm...

all three Orings are the rear. I just removed the front to check for burrs and inspect. 

Yes I was surprised on how well slugs were doing. I’ve never shot a pellet out of this gun yet. As I posted earlier, I just finished my first box of slugs.. I ordered some 26.39 grain JSB to try. Maybe the tolerances are just a tad to tight to perform with slugs. I was also shooting NSA 33 grain...

ill use 600 grit on them. that's not a problem. finding Orings locally has become an issue. Home Depot and ace hardware only care standard sizes. not metric. if y'all could guide me on sizes, id be much appreciated. I'm new to the PCP world. I've been reading the slugs transfer energy better at...