Search results for query: *

As A consumer i think 19.99 would be swell...lol Seriously though...without knowing fx company metrics it be hard to say. but given what other products they made and have been sold at id say 1700 for the 700mm and 50 dollar price decrease between the shorter barrels. FX boggles my mind a lil...

I thought 1800 was the whole kit? anyrate fx has always been high price wise. whos to say the 2k price for verminator was justified back then dude....lol To my knowledge there wasnt another gun that broke down with adjustable power and offered barrel change at the time..sooooo kinda goes to my...

Your right. He cuts away to a range shot and mentions 300bar fill and a half mag extra shot count. I would still like to affrim this with fx before i would fill it 300bar. No hurry tho. it be a year or so before id pull trigger on this riffle.

Really? i watched the utah vid and didnt see anything about a 300bar fill? It does say 250bar max fill on the rifle is why i was wondering.

I use a yung heng and a gx-e-cs3. The gx fills my 480cc bottle in rnd 10 mins from 160ish bar. its slower fill time dont lead to much heat so not barley any drop off upon cooling. The yong fills my 700cc bottle from 160ish bar to 300 in a few mins but does do so with more heat. there is some...

Your right. On both points. But its possible to think its a lil overpriced for what it is. I am considering another pcp for lower power pellet shooting to keep my m3 tuned for slugs. If the panthera was cheaper i could make it a high power slug gun and duel tune a non maxed out m3 config for...

Ive watched several factory tours on the tube. While not a engineer i have worked at a company that used cnc both in-house and from outside companies. This company used several custom alloys and basically peices were matched with an air micrometer for tightest of tolerences. I know for a fact...

Nice response. As FX you could of just said we're market leaders with a industry halo product and no other company is doing what we are. As much as I like a company rep defending the price of a premium product i think we will just have to agree to disagree. There is way less assembly compared...

Will The Panthera not allow 300bar fill? The block reads 250bar? The panthera could be nice dedicated slug gun allowing me to keep my m3 in short pellet config. I was looking to get a grab n go rifle this coming year. But also considering to shoot some nrl. Panthera throws a wrench in my...

1213.14

OK.I was getting a lil frustrated. I calmed down and tried again. After lookn at things again and following the directions on the utah air site i realized there is no need for 2 pins really because of where the probe housing sits. I was trying to install like the fx directions showed on...

Thanks guys. Nielson Ammo confirmed the one pin also. Probably why there was lock tight on the screw holding the block. I put it together and fired some shots and didn't seem to move. Maybe get some lock tight tomorrow to make sure. it did move previously causing my fx power kit pin probe...

Thanks guys. when i went to tighten the screw the probe did turn relative to the rod? I think i would feel better with 2 pins. lol And also my pin was in the rear position? Going to talk to a fx tech eventually to make sure. And further 2 pins are listed in the schematics on the fx usa site?

So. I was excited to find my valve stop in the mail today. I immediately set to finishing the power kit install for the M3. I needed to install a new pin probe because the one from the fx kit bent. Which i thought odd because of my mishap with the valve stop i didn't even cycle the action but a...

I hear ya. I'm disappointed. I thought we were going to figure our guns out together...lol M3 compact may be a lil trickier to shoot due to its size/form factor. I have a 700mm .22 barrel ill eventually try to see if its any different as far a hold and follow through. I got my m3 because i...

For Real?

From my limited exp (only1500 pellets through my m3 compact) valve adjustment may be more necessary on a short barrel high power tune due to the op dwell time concerns. And even that may be a result of your aforementioned higher reg pressure required to get high power in a short barrel...

I welcome all input. I'm learning as i go. No matter how much reading or how many videos watched one really doesn't get things till they do them. Videos, reading, and advice can shortn the learning curve a great deal though. It took me more than a few macro adjustments to realize the micro...

Thanks guys. Learned a lesson. Always listen to Ernest Rowe. Also don't be lazy just because its cold and snowy, carry your ass to the garage and get the right tool for the job! ;) Supposed to come today but there was a misunderstanding and i received 19786 instead. No shooting for me till...

This Is part 19616 Correct?