Search results for query: *

Hi, I'm shooting 4 R5M design guns (2x Lelyas, 1 Matador, 1 Long). Purchased in 2019 w/o any trouble so far. OTOH, I only fill to 200 bar with dry breathable air and run at lower power levels. Enjoy, Nugria

This listing has been renewed

This listing has been renewed

Hi All, Looking to purchase an Edgun R5M in .177. I prefer the Long but a Lelya or Matador would be fun also. Project guns are ok. Thanks, Nugria

Hi Fglass, - HW100: Quiet, anti-double feed (that works at low power), and accurate. Not a high power airgun but low to mid power it excels. Cons: LDC is bonded on pretty well on the later airguns. May require barrel removal and heat to get things apart. - Taipan Veteran: Solid, accurate...

Hi All, I've a low power Impact (early) w/o the power plenum, .177. I've set it up for low power shooting. My limited research indicated the low power Impacts used the same hammer spring but a different hammer. My guess was that the counterbore where the hammer spring fits is deeper in the...

Hi All, I recently completed a transaction with peaceful_ruler. Product was better than described, shipping was incredibly fast, packing made it "delivery service" proof. That's good packing. No delays. Communication was swift and accurate. Shipping (actual shipping, not just printing a...

Hi Herwat27, I use one of these mounts to give me 20 MOA from a Picatinny rail. The same is available in 20 MOA and 30 MOA (?) for 11mm dovetail mounts. Utilizo una de estas monturas para darme 20 MOA de un riel Picatinny. Lo mismo está disponible en 20 MOA y 30 MOA (?) para montajes de cola...

Hi Sid, A not previously mentioned: If you don't mind rear side-lever bullpups, the Taipan Veteran Compact isn't a bad choice. The power can be adjusted with the hammer spring preload with good results. (Yes I realize this may not result in the best tune but the Veteran does quite well.) ...

Hi MC357, I think what you are talking is "cascade" filling. Use of the lower pressure SCUBA to get you to a point and then push the rest of the way with the SCBA? If so, this is an off-the-shelf answer that sorta does what you are looking for. Scroll down to see the 2 tank fill. Enjoy...

Hi OP, NH isn't that far :) Nugria

Hi Long, Are you firing a pellet each time (into something suitable) you work the cocking handle? The anti double feed mechanism will prevent the magazine from indexing unless you fire a pellet with adequate energy. (You may know this but I'm just checking.) There is no need to play with the...

Hi, The little FX would be a good piece especially for the money. If you are shooting indoors 10 fpe might even be excessive. Your shot counts per fill will keep you shooting all day! :) If you don't mind the trouble of finding one, the Lelya 2.0 in .177 with a Huma 12 fpe kit is a good...

Hi, Have you increased your hammer spring? If you turn it in (clockwise from the rear) to excess the spring goes solid and the hammer will not hook on the sear (lever will not stay back while cocking). Have you played with your trigger adjustment? If that gets adjusted incorrectly the hammer...

Hi Franklink, To close/plug the vent hole use a cylinder with an o-ring piston seal on each end. You just slide it into the reservoir so the seals straddle the vent hole. I got the idea from the Huma 12 ft-lb kits used in the Edguns. In the Huma kit they supply a part as described with...

Hi Meanadidas, If you know how it is shooting at a reg pressure with the 20cc plenum, you could find the upper limit by setting up the TP w/o a regulator and filling to your regulated pressure. Now your plenum is the reservoir volume. You could never exceed that performance at that pressure. ...

Hi Toomuch, I'll give it a shot. Did this occur in a shooting session, after a repair (or adjustment), or after the R5M was no used some time? What is your air source? Are you using dry air or hand pumping? Can you determine where the air is escaping? Out the muzzle, regulator bleed hole...

Just bought a nice airgun from kiba. His photos were excellent, his packing was better than any supplier of new airguns. If you like high velocity, just watch how fast he ships after you pay - instant. Enjoy, Nugria

Hi All, When Nikon got out of the scope business a few years back they were selling very reasonably. There were some minor variations as some have plastic turret caps and some have aluminum turret caps. As mentioned, rather big for a 3-9 but they work for me. Nugria

Hi wyshadow, The questions you have concerning the shot cycle are why I started shooting some of my airguns in the 6-9 fpe range. My first bullpups were based on the Edgun R5M platform which can have quite a snap when the hammer hits the valve. First I just backed off the hammer spring. It...