Search results for query: *

I dont think a new transferport is really needed either. I just had the Huma dual port on my old ST barrel and it is larger, but my reg is the limiting factor anyway untill the high pressure reg arrives. Anyway i wrote a mail to Huma Air where i bought the kit asking about it. I had to contact...

My bad, it is ofcourse made out of steel, no idea where i got the aluminium idea from. However, it still looks to be made in 1 piece. If you look in the oring groove there is no visible signs that you can screw the transferport off.

Hi. bought a new barrelkit for my MK1 impact, but the transfer port is made out af aluminium instead of brass, never seen this before. "All the ones i have seen before have been a combo of alu and brass. The end that goes into the barrel is alu and transferport brass" Anyone seen this "new"...

Just wanted to update this post in case someone else stumbles across it. The leadban is NOT going to affect airguns and rimfires in Denmark from 1/7-24. Airgun ammo and rimfires are axcluded from the ban. This will only affect ammunition for centerfire rifles used for hunting. Also as most...

So, did you die or did it work ???

Anyone have the sizes yet ? Might aswell get this figured out as it will be a problem at some point. Maybe add it to the existing Impact thread - https://www.airgunnation.com/topic/impact-o-ring-list-corrected-with-links/

I have no idea why you have an oring there on your gun. There was not one on my original MK1, and there is not one on the upgraded valvetube im running now. Also, it´s not on any diagrams i have ever seen. "Secret MK2 option" ? I also fail too see what function it could have as the large...

Very happy with my Huma reg. 1.st gen Impact. Original never really worked like it should. 

My .25 and .30 mags are all aluminium, bought in 2016. And im sure because they are all modified. 

I use Ergo on everything that will accept them.

And the hex for the valvestem grubscrew is also a 0.9mm on earlier models, at least mine is.

1. The magazine on mine (1st gen) is held firmly in place by 6 rubber balls. Without the barrel installed i have to apply some force to insert magazine. Check that the rubber balls are there or you might be able to loosen barrel and slide it back a little. I have 5 mags in.25/.30 and all fit...

I have plenty of all the orings, (will never buy an Ebay overpriced "kit", when you can spend a little more and get 10+ kits worth of orings). The only problems i have had since i got my Impact have been creeping/spiking regulator and the stupid x-ring. Regulator got HUMAfied (still at 140bar...

I tried a viton oring 2.90x1.78 (original size) in Dura 90 so a little harder, but it also failed. Good to know, if it comes down to a new tube i will make sure to get the nut aswell. I will try to rough it up a litttle, it is pretty smooth right now. Will post results.

I have contacted fx support in Sweden. Will see if they have a solution. That oring size is not going to fit in my current valvetube. /thanks

No problem there, It is a little bit shiny, and also dont have the number of pellets through it to make flatspots. All the above is working fine, I have a Huma reg installed and it keeps the pressure when you remove the tank, so valveseat etc should be fine. I have been careful and...

I dont have any larger orings at hand so will have to order some. But i dont know if i can fit anything larger inside or what size i should try. I also dont know if FX made changes to the valvetube on the newer ones or if they just used a larger oring or something. And i have not been cheap...

So my Impact is leaking from behind the powerwheel on the side, So 99% it´s the x-ring inside valvetube. I have changed it 3 times today and still leaking. Cleaned inside the tube, the valverod looks fine, using blunt tool to seat the x-ring and also changed the 2 o-rings on the outside just...

I asked the same question 3 days ago and apparently they work. I have 1 in the mail, should arrive in a few days. Will post results. More inputs here. https://www.airgunnation.com/topic/anyone-installed-the-huma-reg-on-their-impact/

I send a message to the seller and few mins ago even though item is listed as unavailable. Will see what happens.