Search results for query: *

They'll probably last forever too lol

Also FWIW, I run a Huma regulator with heavy Belleville washers at 180bar in .22/.25 (about 205bar in .30). 350mm LW in .25, shooting 34gn JSB heavies at 895, so the extra weight also helps recoil.

The factory rail was terrible on the Panthera .. borderline criminal given the interference issue that shifted my POI as much as 0.8MILs at 50y when my bipod was mounted on the far end of my 700mm 22cal. The original Leshiy is still my favorite PCP of all, but I liked the minimalistic Weaver...

That kind of downtime isn't common (HA and DR is cheap). Guessing they either lost a no monolithic data data tier or they're doing SIR from a breech.

Greetings AGN! I have two hand made .22 caliber FX barrel adapters for the Taipan Veteran. I made these 2-3 years back and kept them in my personal stash. Both are made from very high quality marine brass, which I found DOES make a difference harmonically. Definitely not making any more after...

This listing has been renewed

This listing has been renewed

This listing has been renewed

This was once Michael Wendt's Katran that was featured in the AEAC review videos. The cosmetic work/ Cerrakote was done by Utah Airguns' custom shop. I made a much better and stronger valve for this rifle as the factory valve was like a needle that was penetrating into the super soft valve...

Excellent for NRL22 or long range pesting from a tripod. This Kraford & Lypt rail solves the POI shift issues that plague the rifle with the factory rail as it doesn't bump into the shroud like the factory rail and other aftermarket rails. Shooting MOA or better for me with a variety of ammo...

This has an excellent 15.7" twist CZ barrel and comes with the new v2 balance valve from AGT. Installed the new valve and resealed the rifle about 3 weeks ago and it's shooting great! It's a beast, accurate and consistent, and it just works without fiddling! Added a Picatinny rail to the hand...

The classic Leshiy is small, lightweight, and virtually indestructible. This has a custom hammer spring with a PEEK preload bushing that gives it a huge range in power and efficiency. Huma regulated. I have (3) Leshiy's already, so this one can go. Included: Original Leshiy (very few marks)...

Thanks man. Yeah I machined a few different blanks down for the Mav. I think you were the one who had a build that inspired me to run a short barrel with an Emperor. I think the barrel came out to 330mm or something close to that, and had to use a Dreamline cylinder for clearance: It was...

Yeah I solved for that a couple of years ago (it's still going strong)..

IN

Wish FX would wise up and design another rifle for this classic type form factor with an air cylinder. Can't stand the big obnoxious bottles hanging off the front of the actions. The GRS Dreamline is about as good as it gets in this regard, but I never cared for the barrel support system.

I've seen dozens and dozens of bent rods. It was a known issue to FX/FX USA as well. Unless they changed the rod material / spec, and tightened up the tolerances on the connected parts then any of them can get bent over time as a matter of simple physics. As far as the idea using brass or steel...

I've spent a lot of time with my Maverick in .22 and .30 with 10 different barrels that I setup for it. I would never set my second regulator lower than 148-150bar, because I can get the best consistency and efficiency out if it using appropriate springs and hammers for whatever projectile I'm...

Nope, it was straight when I bought the rifle new from UA. They should have used a stronger grade of steel or slightly larger rod diameter. A side effect of it bending is that can break the cocking rod guide, because the guide is a hollow 6xxx grade AL with an M8x1 thread going into the front...

Need a none of the above option to your poll.