Search results for query: *

https://m.youtube.com/watch?v=33-RnJekpLU

I'm thinking about buying an FX Indy and I'd like to hear from those shooters and hunters who own one. What caliber do you own, how hard is it to pump, how many pumps does it take for a full charge, how many shots do you get before it needs to be pumped up, how quiet is it, do you use an after...

Last year, I replaced the OEM piston seal in my TX200 with a Moly-Core seal from Vortek. Since then it has worked flawlessly. The standard deviations are 1.5fps at the muzzle, 1.6fps at 10yrds, and 3fps at 22.5 yards. I would like to know if anyone else has used a Moly-Core seal and if your...

Why are my BC(s), nowhere near the manufacturers or online databases? I chronograph at the muzzle, 10 yards and 20 yards, then I use Chairgun Pro to calculate using velocity change. When I use the manufacturers or online BC, the speeds are nowhere near my chronograph readings. .22, H&N Baracuda...

Is consistency too much to ask? Since 2008, H&N has made the .22, Baracuda Green with head diameters ranging from 5.50 - 5.54, in 12.50, 12.65, 12.35 and 12.96 grains. The first run of 12.65gr with a head diameter of .50-.51, worked best with my TX200, but I have no reason to believe that they...

I'd like to know the head diameter - 5.50, 5.51 etc. Thanks

My neighbor noticed that chipmunks had burrowed beneath the below pictured retaining wall and gave me a call. I setup 12 yards away and at 6pm the chipmunk emerged from a hole in the lawn and ran along the bottom of the wall, I took aim and squeezed the trigger, there was no convulsing; he...

I’ve been using this anti-cant level since 2014 and during that time it has worked flawlessly. It’s made of quality materials and can be adjusted in both the closed and open positions.

As I said in a previous post, I’ve shot north of 100 of these critters and they’ve always been clean, no fleas or ticks. This is the first time that I’ve seen a chipmunk covered with fleas and carrying a tick. I’ve never shot them during the spring or summer only in the fall. Is it common for...

This chipmunk was taken at 42 yards with my .22, Air Arms TX200, using the H&N Baracuda Green 12.65 grain pellets. He was facing me when I squeezed the trigger, the noise of the shot caused him to cock his head just before the pellet hit. The pellet entered on the right side behind the shoulder...

Chipmunks have become a real problem on one of the neighboring farms. They’ve chewed through fuel tanks on the log splitters, destabilized stone footings and left holes around the shrubbery and in the lawn. Since 2015 I’ve shot around 100 of the critters. As long as they stay in the wooded areas...

I bought my first TX200 in 2010, and ran more than a dozen different pellets over the chronograph. The most impressive pellet was the .22, 12.65gr H&N Baracuda Green. Dimensional tolerances were very consistent. Head Diameter: 5.50 - 5.51, Skirt Diameter: 5.70 – 5.72, Length: 8.23 – 8.26. The...

I recently replaced the OEM (Original Equipment Manufacturer) piston seal in my TX200 MKIII with the Vortek Moly-Core seal. Unlike the OEM seal, the Vortek seal was expertly machined with no burrs or seams. I installed the seal without lubricant and it out performed the OEM seal. I'll let the...

When will the Weihrauch HW110 ST be listed on your website? What will the retail price be? Is the Weihrauch moderator included with the gun? Will you be doing a review? What is your opinion of the polymer used for the breach block? Thanks

Steiner is the best rifle scope that I've ever used and it's also one of the most expensive, but that expense translates into durability and reliability. I never have to worry about the turrets working or whether or not it will hold zero. Many of the rifle scopes talked about in air gun forums...

My TX200 lost more power than it should, so I ordered the repair kit and this is what I found when I disassembled the gun. This pin never should have made its way into the compression tube. https://goo.gl/photos/hULHfUQxiu82RD2p7

My TX200 lost more power than it should, so I ordered the repair kit and this is what I found when I disassembled the gun. This pin never should have made its way into the compression tube. https://goo.gl/photos/hULHfUQxiu82RD2p7

We live at a time when manufacturing needs to meet the demands of the customer NOW. Companies that fail to provide the customer what they want crash and burn. This now, now, now society requires shorter development times and reduced R&D cost which result in ongoing or rolling development. I...

How many folks are planning to bag a turkey this fall? (w/airgun)

My favorite air gun channel is AirArmsHuntingSa because it is both informative and entertaining. I am currently looking forward to Matt using his new TX200HC for hunting. https://www.youtube.com/user/MoshDubber/videos