Search results for query: *

nothing like commenting 3+ years later but here goes....lubricants are supposed to work almost on the molecular level...extremely thin coating...I have noticed between polishing the barrel and lubricated (very lightly) pellets with Whiscombe honey that when I do think I need to clean the...

Didn’t measure/count, will do a more thorough job and post.

If it were me I would get the LP spring in addition to the MP…i got ~60 ft/s min to max at 1360 psi reg press shooting 10.65gr 177 with the LP spring

Here is my new collection of Ghost hammersprings: HP2 51.90 mm x 1.33 mm HP 51.25 mm x 1.29 mm MP 49.50 mm x 1.30 mm LP 49.39 mm x 1.19 mm Exact measurements are tricky in that the ends are a compressed partial coil that is ground flat in an effort to achieve a length. I have a...

https://spares.bagnallandkirkwood.co.uk/product/brocock-brk-ghost-hammer-spring/ So 5 different "power" spring options...you would think this would be an "option" that you need to specify when you order a rifle. And, to your earlier point, if I wanted a rife to move very heavy projectiles and...

~175 bar Reg Max 2548 psi/1092 ft/s, 2519/1086 Min 2516/1047, 2512/1049 So ~ 40 ft/s diff Max to Min at 175 bar reg pressure...and muzzle crack loud!

Hmmmm. Tomorrow i will crank the reg up …and see if the wheel does anything at higher pressures

I understand the physics…but i dont understand why they would put in a spring that doesn’t “work”, even when the reg was 156 bar it did nothing. I thought the whole point of the rifle is to be able to tune the ft/s to optimize pellet performance and maximize air use efficiency?

Why? The power wheel isnt doing anything?

Also, minimal resistance on going from min to max…is that right?

Ok will do. Thank you again. So, i dont understand, why would they put a spring in the gun that doesnt enable the power wheel? And why didn’t BRK function ck the rifle before leaving the factory? My Revere was ck, with velocity and power recorded…

Dimensions

1/2 my brain says hell yeah…the other half is saying dude you just scrimped and saved and cashed in all ur chits with the boss and this brand spanking new $2100 rifle aint working out of the box…send it back

So far i have shot it at reg pressures 57, 65, 69, 83, 100, 147, 150, 156 barg and saw no significant change in ft/s from Min to Max. I will set back up and shoot at 115 bar 1667 psig

20+ dry fires till it went from 400 psi to 0, did not vent to do that, did not vent when bottle attached Max 1460/927, 1455/924 Min 1419/927, 1445/927

Will go through reg lower procedure and post 100 bar. FYI i posted this in a diff group, but the two times i have done this i get down to ~80psi and the rifle vents to 0, then when i attach bottle it vents until i cock (quickly) it

1200 psi 83 bar Min 1200/875, 1189/872 Max 1185/869, 1181/868

First, greatly appreciate your interest in helping me and your knowledge. Shoe adj back. Setting psi/ft/s Max 2290/1065, 2297/1064 Min 2290/1044, 2291/1048 And to answer your question there is minimal resistance in moving the wheel from Min to Max

My issue is that the Power Wheel doesn't make any real change in FPS regardless of regulator pressure...I had the pressure on the regulator at 825, 950,1200 psi and again the power wheel didn't make any significant change in ft/s from Max to Min