Search results for query: *

Does anyone know how the 2 regulators of the FX Wilcat MK3 BT 700 mm are preset? Thanks in advance for your answers.

Vulcan 2 tactic cal .22 chrony. 18.5 grains 104 shots awesome Fill to 250 bar end 110 bar. 300 cc 1.- 852 25.- 867 49.- 864 73.- 864 2.- 865 26.- 872 50.- 863 74.- 866 3.- 860 27.- 869 51.- 864 75.- 860 4.- 863 28.- 865 52.- 864 76.-864 5.-...

Hi friends, I have a .22 FX M4 Sniper. What accessories do I need to install to be able to shoot slugs at a good speed and what setting is recommended on the regulator? Thanks for your answers.

Colleagues, any guide on setting up the FX M4 .22 Sniper to shoot 25.5 grain ZAN slugs? I'm going to start setting up my weapon, but an approximate setting guide would help me a lot. Regards.

Does anyone know why my FX M4 . 22 shoots the first 3 or 4 low-power shots, for example, at 880 fps, and then evens out at 920 fps? I use 18.13 grain JSB. Thanks for your answers.

hey look I'm uploading some photos of how I placed the washer the diameter is a little bigger than the diameter of the barrel and I slid the washer without the jacket onto the barrel and then I tightened it with the jacket the washer is very thin so that the jacket sits without tightening too...

Hello, I have the sniper 700 with a bottle and I use it for hunting in the field. I have realized that if it moves a lot when transporting or using it, my poi changes for a few ctm at 50 mt and this is very annoying because you have to be adjusting the sight continuously. Then I saw a YouTube...

Hello, I have a FX Wild Cat MK3 bottle sniper. It happens to be very accurate, but when I take it hunting, it is very common for my point of impact to change, perhaps because the barrel does not have a barrel band and the barrel does not have much support. For a moment, I put a 1.5 washer...

I have the compact tube model and it is only 1 regulator

Yes, but I have noticed that it is only consistent without losing any speed if I adjust the hammer to 920 fps so it does not vary much, only 4 or 5 fps when I stop shooting if I adjust it to 880 then the speed drops if I stop shooting for 5 minutes it drops to 860 Yes

Yes

It is a tube

Yes, but I have noticed that it is only consistent without losing any speed if I adjust the hammer to 920 fps so it does not vary much, only 4 or 5 fps when I stop shooting if I adjust it to 880 then the speed drops if I stop shooting for 5 minutes it drops to 860

I changed it because they say that Huma is more even and consistent ☹️☹️☹️

Hello, could you help me with the problem I have, it's with a Wilkat MK3 compact, I changed the Huma regulator and adjusted it to 105 bar and the 4 on the adjustment wheel to a speed of 885 fps with a 18 gr JSB, it's a .22 cal. What happens is that if I stop shooting for more than 15 minutes it...

Change the suppressor for another one with a different internal design in a PCP cal. 22, the point of impact will change.

Alfredo-Diaz 913.07

bsa r10 mk2 .... I need help please someone could tell me in what position the choke screw goes to the bottom of the regulator. I do not know if it is completely closed how to calibrate its opening. I leave the photo of the screw

I think my problem is a bad adjustment of the power wheel because the turn and does not increase or decrease the speed I am finding out what is the proper fit and how I know that with a small Allen key can be adjusted but what should be the perfect fit? ???

Fx impact x Regulator presure 120 bar Power weel. Level max Vel 915 fps Level hammer 3