Search results for query: *

Been dealing with the guys at AoA for decades, always there for all my Daystate Airgun needs, Airguns, parts, service, tech support, they have it covered.

Remove action from stock, spray areas of possible leaks with Windex, this stuff really exposes even the smallest leaks. Around gauges, where airtube screws into action, any seams in air tube, and the fill area, you'll find it, I have several FX guns and it's usually the gauge or regulator. We...

Yes, I have tested various settings of my Crown MK2 .25 using 25.4 JSB's with 600 barrel and noticed that the gun is more accurate with higher regulator settings, Right now my reg is set @ 145 BAR and I back off power wheel to achieve the velocity I want, right now gun is set right around 935...

I noticed that my M2 Impact was slowly losing air over time, I sprayed down with Windex and noticed air was slowly coming out of regulaor weep hole on RH side of gun, I removed bottle, removed trigger guard, air vented out of rest of gun when I removed bottle so I knew it was regulator rebuild...

Think people will boycott EdGuns because made in Russia ? What about resale value ?

I have several FX Crowns in various calibers and configurations, I thought I would give the .177 cal a try and I am using a STX 500mm liner with extended shroud, set up to shoot 10.5gr Crosman Premier heavies just a little over 900 FPS for best accuracy and power and am amazed how accurate his...

Just use a Dowdy seal, works better and seals better than the FX brass washer and O RING.

I own or have owned just about every brand of high quality airguns, from springers to PCP's, Theoben, Daystate, Air Arms, FX and others, I still have several of them and others have been sold off. The one gun I still ave after all these years is a Daystate Huntsman Regal in .22, never had a leak...

Finally got around to installing the FX Power Plenum 720 on my .25 Impact with 600mm STX liner, with Reg set at 100 BAR, hammer maxed out and valve adjuster backed out I am right at 958 FPS W/ JSB 25.4. I turned valve adjuster in until I was right at 937 to 940. With a 12 shot string, Amazingly...

SOLD !!!

Not sure what gen but action does have built in picitanny rail on top, 500mm .25 cal STX SL.No leaks has AMP regulator. Barrel is wrapped Gray laminate stock.$1100 shipped. 2 mags. CONUS only. Set just over 900W/25.4 JSB. Scope and rings not included.

Great condition, no leaks works as it should, beautiful walnut stock. Comes with two magazines, charger, keys. $1200 OBO , Conus Scope and rings not included.

I purchased this gun new from AoA about three years ago, Ernest Rowe wanted to see if I could adapt a FX STX liner to this gun so I used a .22 500mm STX liner, made an adapter out of stainless steel that looks just like the factory Bantam barrel on the end but the liner slides inside and is held...

I purchased this gun new from AoA about three years ago, Ernest Rowe wanted to see if I could adapt a FX STX liner to this gun so I used a .22 500mm STX liner, made an adapter out of stainless steel that looks just like the factory Bantam barrel on the end but the liner slides inside and is held...

I have two like new San Rafael FWB 124's, I had to molest both due to typical original piston seal disintegration, while I had guns apart I installed complete ARH Pro Mac Kits in each gun, one has full power kit while the other has the slightly softer kit. The full power kit shoots 7.9 JSB's @...

I have the same gun in my collection, sometimes it would shoot good and next time spray pellets all over the place, tried a long list of things that made gun better but not being satisfied I went more extreme. I had a 500mm FX STX liner in .22 that I knew was super accurate, I made an adapter to...

FX Impact .25 with Earnest Rowe upgrades, power plenum on bottom, valve modified and transfer port enlarged to 9mm for better flow. Regulator set at 100 BAR and shoots 25.4 JSB’s at 930+ FPS and gets tons of shots. STX 600mm liner, If you turn up regulator you’ll get more power to shoot heavier...

I have a Impact with the FX PP and another with the Earnest Rowe PP and the ER PP attached to the bottom of block is more effective and efficient.

Drill the grub screw out using a left hand drill bit available from McMaster Carr, left hand means you drill CCW instead of CW, most of the time bit will grab the screw and turn it right out of threaded hole. I have a whole set of left hand drill bits for this exact purpose. If screw doesn't...

I have a nice Brocock Bantam Sniper HR .22 that I would like to trade for a similar value PCP in .177, comes in original box with all original paperwork and accessories. Message me what you have.