Search results for query: *

Hello. I’m looking for Varmint Knocker slugs, Again. I lost Dales info. Would anyone know how to get ahold of him? Thanks 

By now everyone should know FX has updated the app it’s a little better but has a long way to go to be a good app. Still have to connect to Bluetooth every time you do anything, the velocity was on average 10 FPS lower than Caldwell readings and not consistent reads, and the voice feature...

Thanks for pointing this out! I was wondering what those were for but as soon as I saw this thread I new what they were. no need to buy a rig. 

Thanks very much! I don’t know if that can adjust for length it doesn’t say. But I don’t think Utah airguns ship to Canada yet. But I’ll ask. Thanks again.

I’m looking for a length of pull adjuster for my FX Crown. I need at least 40mm more. I have 3D designed a part that I might be able to print but if someone has any thoughts or ideas I would appreciate it? 

Thanks, Johan at FX told me that the first run had 2 groves but this new batch has only one. But he also recommended that I measure the twist rate to be sure.

Can someone with a .25 cal slug liner confirm for me that the .25 slug liner only has one grove around the breach end of it, or does it have two like the .22 slug liners? The one I was sent only has one grove and I haven't measured but the twist rate doesn't seem to be right. Thanks.

Just an update. FX is replacing the faulty gauges. So they are looking after the defective manometers issue for those of us with those! I was reminded by a member that 158 bar would still be ok for the reg. and even FX says 160+ should be ok. My measurements were made with just my pump gauge...

Yea I’m good and FX is sending new gauge! As for the discrepancy I used my pump gauge to check the two FX and it also could be off a bit. FX says the AMP reg should safely go up to at least 160. So maybe it’s out more than the 8 bar. It seems like if I go over 150 the reg starts to screw up. So...

Yea that's why I thought I would report my findings here. Thanks also to all those with the previous posts that helped me find out. 

To bad only Yankee’s can enter this! What about the UK and Canada and other countries they sell this UK gun in? 

So I think I found out what my problem was. The setting would drop after shooting a mag full from 150 to 145 bar. Couldn’t figure out what was going on unit I got a huma reg to replace the stock one and had to remove the manometer so I got it checked. It was showing 80 + bar higher than what it...

So I think I found out what my problem was. The setting would drop after shooting a mag full from 150 to 145 bar. Couldn’t figure out what was going on unit I got a huma reg to replace the stock one and had to remove the manometers so I got it checked. It was showing over ~ 80+ bar ( hard to...

Thanks for this thread! I have a crown and was having problems with the reg pressure setting staying put. The setting would drop after shooting a mag full from 150 to 145 bar. Couldn’t figure out what was going on unit I got a huma reg to replace the stock one and had to remove the manometer so...

From what I have found the pellet liner b 600mm .25 cal twist rate is 1/16. 

How does one find Don and these varmint knocker slugs? I've looked on line and here someone gave a link but it's a dead one, And does he ship to Canada? 

I have to change my comment and say that FX has treated me good. See my final post about replacement of manometer. I also got a new plastic reg piston for free, woohoo, Anyway for those of you with the AMP reg like mine good luck and if yours works may it keep working. Big thanks to Huma for the...

Good some people are happy! To bad it's not all of us. 

At first my rifle did experience creep it would raise the pressure while it sat over night. I contacted FX and was told it could be the piston oring, and to check that and clean it. They also sent me a new piston but the old one was still good and exactly the same. And after cleaning the creep...

Yea FX has screwed the pouch on this! I won't buy another FX either. I was looking at their Dreamline but now NO WAY. I can see why Daystate guns are taking over the shooting competitions. I won't buy any FX parts either if I can help it.