Search results for query: *

I have the fx crown walnut stock for a little while now. I'm looking to find oil / wax ???? or some other product to restore the finish as it is looking a bit dull and the cheek piece seems a tiny bit rough. I looked in the forum, but didn't come across a product, probably my bad search...

There is a video from AEAC on here where he uses 50/50. The link is a couple below yours. or... https://youtu.be/Z0YYKGUvcGk Cheers

Can't wait to hear your numbers lol. I have the .25 and I wouldn't describe it as whisper anything. Caveat... I'm in Canada.. and we don't have the extended shroud or moderators.. So I'm really interested to see the difference. Stays safe

Racingbirds, Mine has the exact same 'hole' as yours. I thought that was supposed to be there.... no?

I'm good with mine. I do tap them down to make sure they are all aligned prior to putting the mag in

Great post. Looking forward to your solution for mounting the rail.

Great story. Hope your business does well.

I got busy, clicking away and found myself on this page when I was looking for a compressor https://m.aliexpress.com/item/32831137727.html?gclid=EAIaIQobChMI1NuU6Izx2QIVRmV-Ch0e4gaoEAQYASABEgJmyvD_BwE Don't know what to make of them. Perhaps someone with more knowledge will pipe in. Thanks

I dont have a muzzle break on my fx crown. I am able to twist it and pull it forward.. I have pulled off the outer shroud. There is only the barrel underneath. What does the USA one have that my CDN one doesn't?

Still on my quest to make my Canadian FX .25 crown as quiet as possible. I received a suggestion to use an air stripper. I looked on youtube quickly but much of the videos are in a foreign language. Wondering if anyone here has used one or what your thoughts are? Thanks

I'm going to take the plunge on this one I think. I'll post my review. It will probably be 2 yrs later when it gets to Canada though lol. 

Nice. I have to say my dealing with Travis has always been great. I'm going to post soon about my experience.

Here are the full photos. Cell phone (poor quality). I'll take some better ones with my good gear later this week. I like, but it is my first airgun, so my comparisons are limited to powder burners. If I could quiet it down, like it is on low power, I would be really happy. I tried...

Thanks All. Yes.. after posting I had already watched Tom's video (thanks Glem). Quite good details I must say. Your other one on the bipod is also great :) If I put one on I might as well do both lol. Yrrah.. mine has no sound moderator on it either. So we are more alike lol. It is...

Have to see if everyone else has a hole and I don't. Any other Canadians on here.. Can you see if you have a hole lol. Looking primarily at the walnut stock. Thanks If.. not.. then what are my options? I suppose all I can do is take it apart and I have no idea how to do that yet.

Have to see if everyone else has a hole and I don't. Any other Canadians on here.. Can you see if you have a hole lol. Looking primarily at the walnut stock. Thanks If.. not.. then what are my options?

Nope. I got nothing like that. I don't know how to post a pic.. but If someone sends me an email.. I can give it to them to post

So. I finally purchased an FX crown. Getting some teething problems. Trying to figure out how to adjust my regulator. The manual shows a laminate stock with a hole that allows you to increase the regulator pressure. I have the walnut stock and there is no hole. I haven't taken the gun...

I posted this over in the PCP forum... I need my FX Crown .25 to be quiet as possible, no silencers allowed in Canada. Right now I 'm trying to remove starlings at under 50 yards. I want it to be as ethical as possible, so before I go changing settings I would like to know what I should...

I think this one is going to be a hit. I'm going to take the plunge when its out.