Search results for query: *

Ok so the o ring I need to fit is indeed 9x1.5 No matter what, I just can't get the seal to sit inside the chamber I can't help but think the surface has been damaged, which is why I can't get the o ring to fit I get half the o ring to king of sit, but then can't get the rest to fit Is there any...

I can't find anything using the search option so here goes.. I have this very early impact mk1 and need to replace the o ring inside the regulator chamber.. Anyone know what size this is please? Also, what's best way to actually fit this o ring? As it seems to be a tussle to get this to fit...

Ok it’s own without a shrouded barrel, it’s not effective. However, on my wildcat .22 sniper it’s brilliant 

Update: after a few tweeks, my gen3 is now giving the same performance as my huma modded gen2

So I have a wc mk3 gen3, brass reg It’s not giving me the same or as good performance as my mk3 gen2, amp reg both sniper .22 Gen2 mods were huma reg with spacer (amp), huma transfer port (not the current v2 tp, but the previous one which I think was slightly smaller). This shot the jsb ko...

So this is the gap. I’ve ended up using 1 o ring on each end and it seems to have sorted the slight accuracy issue … back to 1 hole

Ok so I can happily use tape to get a very snug fit … but this still isn’t going to cure the problem of still having a small gap … ie the carbon sleeve doesn’t quite cover the whole barrel/liner 

When fitting a fx carbon sleeve on my wc mk3 sniper, there’s a slight gap ive used 2 of the o rings to fill this gap, but accuracy isn’t quite as good as without the carbon sleeve is there any other way around this ‘gap’?

Ok so I tried the above stated method again to remove the protruding probe, but didn’t work in my wc theres something I can’t find nor is it clearly shown in Ernest’ videos. When reassembling the sear, where does the hammer have to be placed? On which part of the hammer does the pin sit which...

So I’m unable to use the huma pellet/slug probe in my wildcat mk3, as it slightly protrudes meaning I can’t load the magazine its about 1mm longer than the fx probe any way around this? Or have I received a ‘faulty’ huma probe?

Great thread! so I have a .22 wc mk3 sniper incoming Anyone already know what’s best speed for the following: 23gr Nielsen .217 23gr Nielsen .218 jsb knockout .216 jab knockout .217 jsb monster redesigned

Finally got round to fixing my r3m and the oring you pointed out was indeed missing from the start and I didn’t think of it neither so thanks again for your help with the huma reg and hammer weight fitted, 34gr are maxing out at 860 my r3m is the standard version anyone able to get more...

Thank you nugria! will fit the huma reg and plenum in the next day or two, but I already know you’ve answered my problem I just didn’t see anywhere or read that a oring had to be fitted there makes total sense tho and kinda kicking myself for not noticing that before appreciate your help...

Yes, the bleed hole is in between those o rings and yes that’s the problem, the huma reg isn’t sealing with the huma plenum body there’s no o ring which goes on the huma reg where you’ve pointed out, and it seals on the tester ok without an oring there too The huma reg goes in exactly where...

Above is edgun regulator assembly and below is the huma plenum and reg both diameter measurements are the same I’ve tried white tape under the o ring and silicone grease inside the cylinder and also on the plenum, but still leaks from breathing hole when I start to fill any ideas what the...

I’ll take some pics on the next disassembly but I did measure it against the edgun reg assembly and it seems the same

Ok surprised but also glad I’m not the only one with this problem air clearly isn’t sealing and common sense would dictate the problem is due to the plenum .., either being minutely too small in diameter or some kind of hair fracture in the body itself I’ve told huma about this and I’ve paid...

After fitting the huma reg and plenum, air leaks from the tiny breathing hole in the cylinder when I start filling reg tester shows the reg is fine, but I still changed the seals on it strange, as no leaking if I use the huma reg with the original edgun reg body as a plenum this leaves me...

Thanks think I’ll stick to just the 2021> huma reg then, as I’ll be using a moderator on the shroud 

I’m looking to fit a huma reg on a wc mk3, but it’s the newer 2021> version Anyone know if the dreamline external plenum will fit the wc mk3?