Search results for query: *

My hand pump started to heat up and produce moisture that got in my gun even with a new filter. I tore the pump apart, cleaned it good, changed a couple of "0" rings, applied silicone grease and it works fine now without overheating. I tore the gun apart and cleaned out all the moisture and let...

I purchased a chrome-moly steel 12oz paintball co2 tank, I want to use it on my pcp that has a 2900 psi fill, can anyone tell me if this tank will hold 2900 psi. I'm buying a fill station valve that is rated to 4500 psi that will screw into this tank. I know that this tank is a lot heavier build...

I'm thinking about getting a 48ci 3000psi Tippman air tank to fill my Hatsan Flash Wood 165cc air tank to 2900psi while hunting. Does anyone know approximately how many times I could fill my gun with this set up. Thank you.

I just purchased a Caldwell chronograph with the lighting kit. My problem is I have a really hard time getting it to record a 10 shot group, if it registers at all. I get 2-3 registered shots out of 20 shots. I have tried everything I can thank of, bright sun lite, partial cloudy, overcast...

Does anyone know what bar the reg is set at on a Airacuda max. Thank you.

These guns really amaze me, I thought my Crosman 760 Pumpmaster done pretty good at 11 yards. I just recently purchased 3 Daisy 880 powerlines, one is a 1973 Powerline still working on it, the second is a 1980 powerline, the third is a 1996-2005 powerline. The 1980 and the 1996-2005 are...

Looking for some Information on the brand name of this side lever springer .177cal. Any information would be appreciated. Thank you.

I just completely remaned a Beeman S1 new spring and piston seal. I greased all pivot points and the spring and hammer and a light coat on the seal and all the parts of the trigger mechanism. I did notice on the cooking arm where it sits on top of the hammer and slides inside the pressure...

I'm refurbishing my brother's Marksman 45 .177 cal rifle. The trigger blade is plastic and shows a lot of wear, to the point that I cannot adjust the trigger any at all and keep the safety working. I found a partial trigger assembly on ebay from a Beeman Sportsman RS2 that looks to have a metal...

Has anyone ever opened up the port on a springer. Seems to me that if the port was a fraction smaller then the breach more air could hit the pellet quicker.

Trying to reman an old springer for my brother but I haven't been able to find a name. The pictures will show all I can find, hope someone can point me in the right direction. What was on the end of the piston has completely crumble and it did not look like rubber lm woundering if these guns can...

Just picked this up for a 30 pack of Bush beer. It's pretty rough but some good old TLC and a lot of elbow grease, I thank I will have a pretty nice riffle. Going to do some work on the trigger and sear, some shims to take the play out of the barrel tube and pump tube and the barrel. Next on to...

Hi folks, hope everyone is having fun with their air guns. I'm shooting a Hatsan Flash Wood with a Huma-Air regulator installed set at 160 bar. From 200 bar down to 150 bar I get around 16 shots. Don't have a chrono yet so I don't know what kind of speed I'm getting. Question: If I turn it down...

I recently bought a used Hatsan Flash Wood in 25 cal. After total reseal, deburring, grinding and polishing off sharp edges, I now have a gun that I can disassemble and reassemble without cutting 'o' rings and a bolt that slides very good. I installed a Huma-Air regulator set at 160 bar and a...

I recently bought a used Hatsan Flash Wood in 25 cal. After total reseal, deburring, grinding and polishing off sharp edges, I now have a gun that I can disassemble and reassemble without cutting 'o' rings and a bolt that slides very good. I installed a Huma-Air regulator set at 160 bar and a...