Search results for query: powder coating

Remember that they should still be sized correctly after powder or your results will be tainted.

I've been running powder coated subsonic 30 and 35 cal bullets in powder burners for years. The bore stays remarkably clean, velocity I never did a side by side comparison. The bullets still engrave fine and the rifling is only there to cause enough grip to impart spin. Glock and fx have...

For my .510 Texan slugs are .50 to $1.00 a piece..Owww..I took 200 lbs of horded wheel weights and turn them into powder coated slugs that shoot targets and critters equally well..I have shot 300 lbs of lead through my .510 Texan at 450 grains at piece mostly..For my .22 cal condor i cast 39...

I cast and powder coat slugs for my Airforce platforms in .510 up to 650 grain spire Point Boat tails..I shoot out to 200 yards now and soon to 300 yards with a lil work on the new range.. Check out castbollits.com for learning about casting...

Are the originals powder coated? The recent one's have better trigs?

200 Yard Range 🙂 First time use....510 Texan and Free wheel weight lead NOE cast powder coat 450 grain 820 fps..197 yards. No sorting just sized and lubed..

Wow great job on first time casting!!!! Hollow points can be tough....I missed a few key details when i started casting..took me a lil bit to figure it out...Give powder coating a try....its pretty easy...it helps with leading for sure...

Following this one.

Yeah, I don’t know what's going on with Presslug and the larger dies, and even with the .2173 they had listed that was never available, that's borderline for most. One guy here had to powder coat his to shoot well but hasn't posted anything for a while. It's a shame you need to invest more and...

I like using HBN powder for a lubricant I add some airsoft bb's to a ziplock baggie..then about 1/8 teaspoon of HBN and mix it up until all the bb's look white then add the pellets and tumble them around for a few until they have a been thoroughly coated, but not looking like they are heavily...

...lead. Some claim a velocity improvement - hard to say among other variables. I do prefer it to bare lead. Poly coating (basically powder coating) is another option that has some fans among powder burners. If you don't mind sharing your materials, times and temps for hardening and...

These are .510 650 Grain Spire Point Boat Tail at .5 B.C. They are powder coated. This slug shoot s good in my .510 Texan. With the T Rex you should be able to get 1000 foot pounds at 300 yards.. These are free for me..They came from horded wheel weight s from the 90s.. Have a real...

Again I tried to powder coat my Mk 1 stubby, same bad results I got from a few months ago. All the other guns like my S&W 78 & 79 came out very nice. So I think it has too much porosity and oil is impregnated on it. Decided to just polish this for now until I can gain access to a large...

I too moved to just using lubalox and Johnsons paste wax mixed together and a tool that lubes and sizes simultaneously. The process for powder coat was too time intense. I do shoot powder coated mostly but buy them in bulk pre done. As for gaining velocity. A light lubing with silicone...

Having never handled a RAW air rifle. The material used for the block, is it the same as the Theobens from back when they were blued steel ( my guess ) or billet aluminum and powder coated? I do like a chassis but I much prefer wood and metal. I do prefer the chassis on the RAW then the bland...

I have been getting results casting a 39 grain spire point at .225 diameter soft pure lead and then powder coating.. And not sizing them shooting in a factory Airforce Condor Lother Wather 1 17.7 twist barrel.. I cut the choke off the end and hand lead lapped barrel. It is .221 in diameter...

did you throat the breech end of the barrel to help the larger bullet fit? I throat 30 caliber powder burners for cast bullets with 1.5 deg throating reamer and notice an improvement most often.

After powder coating then size to your bore diameter... A a little lube of your choice..

In the week i cast and powder coated 12 lbs of 39 grain .225 spire points for my Airforce Condor..I always have aleast 100 lbs of cast slugs for my .510 Texan or im nervous... i have to produce my slugs to be able to shoot and practice the way i want.. Price is going up...lol $1.25lb for pure...

I have lots of .510 cast powder coated N.O.E and Accurate Moulds slugs.. 450 grain to 650 grain .5 B.C 650 grain Spire point boat tail...I have four different molds in .223 to .225 diameter.. Can be sized down to .221 diameter.. Will trade for anything pcp and optics related...