Search results for query: *

300+ Yards? What is your target an abandoned barn? Expect 10-20moa groups and huge scope elevation erector assembly. It can be done, and has but its not anything like a PB. You will need expensive equipment, ammo, compressor, etc. A Gauntlet 30Cal isnt going to get you where you want lol. But...

Yes exactly. You can use an allen key to adjust the preload on the hammer spring. It is designed for fine tuning your last few fps. But if it is all the way backed out it can really lower your overall speeds. So turn your power wheel so the hole is at 6 o'clock and you can adjust the set screw...

Hello Im looking for just the Shroud Assembly for either an Impact or Wildcat/Maverick preferably with the correct air stripper diameter for a 25/30Cal in 600mm. I can use a 177 or 22 Cal too. I have lots of FX Parts to trade if you need something or can pay through paypal ff. Thanks ETA...

Well there isnt really a need for the reg gauge to go so high. 250Bar is probably the best since gauges are more accurate in the middle of their range, and you can read a lower value gauge more precisely. So if your regs are set within the FX suggested ranges, a 200Bar gauge is still a great...

And for reference my Wildcat Compact Tube version was able to push 30 Cal Nielsen slugs at about 860 fps on ~140Bar.

First off I think you need to read your owners manual again. FX regs wont last long set over ~150Bar, that includes the front reg. And you wont have enough hammer strike to use 150Bar on the rear reg. I suggest watching a few videos posted by FX/Ernest Rowe on how to tune your Impact. You will...

Gamo Coyote 177 JSB Slugs 10g MK3 @1000fps is amazing close range squirrel medicine.

I could be wrong but I think this is a synthetic stock that was hydro-dipped and has a matching length of pull spacer.

A Ground Squirrel's worst nightmare come to life. Many of them, this is the last thing they see. Kinda like a Millennial Michael Myers.

No, because the housing will also bend. The CF Sleeve has the best tolerance fit and virtually no ability to squish like orings do, but you could still in theory bend the assembly. A tensioner with the CF Sleeve will give you the strongest truest setup on an FX imo/ime. But if the tensioner isnt...

As promised here are some Sears Family Photo level pictures of my sling setup.

That Ghost is rad with the CF shroud and 0DB :ninja: 👍

Mr. Ernest Rowe has many videos covering this issue with the FX barrel assemblies. You can actually put a permanent bend into a barrel liner if you tighten the muzzle jam nut too tight, and it doesnt take much. Same with the whole assembly when using a tensioner system, you can bend or warp the...

The HN Slug II are basically pure lead and very very soft with a huge cavity. They are designed to open up a lot, and as soon as possible. In contrast previous airgun slugs have been made with harder lead alloys and have a tiny shallow cavity. Kinda like comparing an FMJ to a HP/SP in...

Any pcp internals are going to made from a combination of brass aluminum stainless and rubber for the most part. All are susceptible to water/debris ingress and thus, corrosion. Any moisture and debris that gets into your very delicate tight tolerance pcp will degrade its performance and service...

I think you will find that many Urban owners opt to remove the barrel band to help reduce poi shifting. I have 4 Gamo Pcps and 3 of them dont have the barrel band, and the 4th is virtually brand new and I havent removed it...yet hehe.

Imo all Hawke scopes are budget scopes. None of them have great glass or internal hardware, but the prices mostly reflect that. Athlon/Arken/Vortex etc have much better budget options in my book. I bought one Hawke because of their stellar reputation in the air community, but sadly will never...

This listing has been renewed