Search results for query: *

Youre right. The 6 amp seems more reasonable. Can just bypass it with a jumper wire until the caps fail. 8 amp thermistor might prolong its life. No point in buying a solder kit for a $20 supply. If it fails, buy or build bigger. Can use an old PC supply for the cost of some wire nuts.

6 amp NTC thermistor seems kinda low for ~30 amps to flow through it. All they should do is slowly ramp up power (changes from like 1 ohm to 0.01 ohm) so the caps dont blow on powerup.

Are you sure its not a breather tube? Yong Heng oil container needs to breathe or it can explode.

Probably "power factor" effect at play and they sized things for average power instead of peak in the compression cycle. My supply was 40 amps, I linked a cheap 50 amp, beyond that its more than extra dollar or two.

No. I need to read more. Maybe want to drop the fps in the future but 22gr pellets didnt need any scope adjustments when i zeroed with 14.3gr at 17 yards, both hit same dime hole.

Measure it but its probably a 3/8" hose and theres very few pumps to choose from. Sometimes they list it as 0.3 inch.

Box says Snowpeak, the fine print on the rifle mentions Lancer. I'd assume its the same as the Remington except without the narrow transfer port. I only mess with the triggers for now. I dunno, theres a grub screw. I havent checked if its for anti rotation or holding it on.

Argh, in the two hours I spent packing the car, forgot to bring the soldiers. Luckily had a stack of these 3d print targets. The big ones are dime size.

Lancer T-rex bullpup: $211 3-9x scope: 23$ Cheap bipod: $20 Hand pump: $50 Total: $314 Add $500+ for eletric pump, good filter and basic tank.

I printed your first link and they worked good. Umarex Gauntlet mags do not fit. Looking down the barrel the T-rex mags have a curved cutout on the left for the bullpup bolt linkage.

500 rounds through it. Crosman 14.3 domed With a wobbly table I was able to consistently hit pennies at 50 feet with a 9x scope (4.5moa). Gets mildly concerning loud having ear so close to chamber, I would want to wear an earplug in right ear for future target sessions just because it is...

FWIW, the 3/8x24 standard labeled discs are loose when threading but didnt wiggle or leak when tightened. You sacrifice 0.5mm of thread width however. I didnt want it to fly out so I went back to 10mm style disca.

Something like this and cut the ends off your existing cables to reuse them. https://www.amazon.com/Hosyond-Universal-Regulated-Switching-Transformer/dp/B0CQK57GP9

lol. The GXE EK2 amazon description. This is an $1800 compressor. China is determined to push iffy 10mm burst discs, industry standards be damned. Anyone have a clue on the math on doubling a burst disc?

Sounds like dead power supply, mine runs hot as hell. These things tend to use the XT60 plug and usually include a 12v battery clip, id try that. Its a $20 cheap switching power supply that gets hot. Often they have a minimum load requirement or else they tesla coil themselves to death. If I...

Thank you, printing them up now.

Bam, alien targets.

Paper over dollar foam.Headshot challenge.

20m target making. watered down white glue, dirt,.dollar store 2x3 foamboard. needs more painting.

Trying to buy or 3d print T-Rex (bullpup) magazines since I lost mine. All the vendors I find are overseas and want $90 for one when its a $20 item. Found a $15 3d print model but the instructions for the spring are in spanish and the two words "something wire" and the xyz dimensions and the...