Search results for query: *

Given the extremely high cost I think I'll stick to Bubbly Leak Solutions it only cost less than $10.

The MSDS says very little other than it is 98 to 100% distilled water. What I want to know is comprises the up to 2% other stuff. Since it has a very low conductivity I have to assume that the up to 2% isn't salts in solution.

I'm thinking about it but might be messy. Might have to take off the legs to fit into a garbage bag. If it's the same one I saw last time they're pretty smart and when I crack a door open to get a shot off they immediately run off. I noticed this one has some big ears pointed in the right...

Leftovers from making chicken soup I left for the raccoons. But the rats were eating it the last few days and now a brazen coyote came by while they were still daylight.

With an fx you better carry as many O-rings as you do air tanks. :ROFLMAO:

I put a lot of bird seed and a bunch of chicken out there. The rats comes by 2 to 3 times a night, but never stay long and only stays still for 2 seconds at most. It grabs a bite to eat and leaves. By the time I react to the alarm it is long gone. I don't have the patience to wait for hours...

I'm sane not nuts like these people.

So I can eliminate them. They cause a lot of property damage and swim and $hit in my pool! Now I planting a vegtable garden have to keep critters in check. Therefore I'm proactive.

I just checked the coon feeder the skunk ate about 1/2 the food. I will add another inch to the spout that should stop the skunks from eating, but still allow the coons to get to eat the main course, after which I will give them their final dessert of Pb! That's why I don't recommend coon cuffs...

I have shot them in the past. Twice it smelled up the backyard. Once it was so bad neighbors over 200' away at 2am start looking out the window wondering where the smell is coming from. My wife was so pissed she was mad for more then a week! I don't want to risk a sink bomb. Shooting it is the...

Traps seldom work because I catch more birds and sometimes squirrels if I'm real unlucky y'all piss off a skunk.

The skunk comes by quite often and cleans out my coon feeder. So I made the spout 30 mm longer hopefully that stops it. However today the skunk came by and got some food out but I don't think he cleaned it out. Hard for it to reach that far down. I refrain from shooting it because I don't want...

They just don't stay still for long. By the time I get an alert on my phone they are long gone. They only show up 1 or 2 times a week.

I can't say how well it would work for a 22 or 25, but for a 177 this is real quiet! https://www.airgunnation.com/threads/huben-gk1-v3-red-dot-mount.1321122/page-3#post-1852150

How did you get the right part number when they blew up?

Yep, I was surprised one night. 2 days before probably got the mother. Then 4 youngsters 7 and 12 lb showed up 2 days later. Get a double, while the 2 other ran away. Withing 2 hours the 2 were back. 2nd double of the night. 4 within 3 hours! BTW for those debating 850 vs 950nm. Neither the...

NTC probably stands for negative temperature coefficient. It's like a variable resistor it changes resistance based on temperature. Since it's negative temperature coefficient probably gets less resistive as the temperature increases. It's a current limiting protection device. Problem is finding...

I don't know the flow rate, but the output of the CS4 is a little more than stated in the manual. I measured the power used by the CS4 to set the pressure level. I set it so it is below the maximum power reached testing with the dead head plug to maximum pressure 350 bar when I fill to 300 bar.

This coyote was digging around where the coons dropped food. I opened a door 24 yards away on the 2nd floor very quietly and slowly, but it still spooked the coyote that promptly left the scene. A least this coyote will be much tougher to remove than coons.

I wouldn't recommend 15 psi input unless you want to prematurely wear out and break your compressor. I use 3 PSI and if I only fill to 300 bar that's no worse of a load on the motor then filling all the way to the 350 bar that is capable of.