Search results for query: hammer adjustment

actually the hammer screw/adjustment will move on the threads, its internal kinda

Does that also apply if the airgun is regulated?

Thanks for the response. Yeah, thought it was Ambi. Great. I prefer side lever on right, so no issue. I’m hoping there is a space for a small carve out behind the action so the HS can be adjusted in the stock. I’ll ask Shane at AoA.

For the U2 600mm .177 I polished the hammer spring seat around the shaft, sanded and polished the base that sits against the hammer adjustment. Polished the hammer spring everywhere but the spaces in-between as well as the hammer contact surfaces. And reduced the reg again by another 10b to test...

Ear is the best way to adjust hammer and valve.

I just got the 250z in .25 and was curious what everyone else's experience is with the hammer spring. I've increased the reg from 2000 to 2400 and I'm having a hard time getting the FPS to settle. I seem to get highest speeds at 0-1.5 turns in, but the ES still jumps around 5-10fps and it'll...

I have the tungsten hammer weight in my M3. With the reg at 165 bar with stock hammer weight, you would have the hammer spring tension almost maxed out. Keep the tungsten hammer weight. With the valve adjuster 1.5 past the 4th line you are probably wasting some air. When you get your new...

Thanks to all who offer advise for a fix . I was able to get it straighten out . I had to put more tension on the hammer spring with the micro adjuster and then after that it was getting the reg pressure and hammer setting to work in unison. I have the reg set at 145 I was able to tweek out...

You guys need to back that hammer spring adjuster off. Or continue to have valve issues.

No, the one that needs to be removed is just a centerpiece for the hammerspring so it doesn't bend. The round piece where this screw goes in, is actually a screw itself and can also be turned in or out to adjust hammerspring tension, but you need something with 2 protuding pins to be able to...

Correct. To OP. When you see the highest number before you adjust and the fps drops. Dial back to.thst position and then 1/20- Yes. You'll adjust. See a number then. Adjust. And youll.get an obvious decrease. The katran is a bit more pronounced with this than most guns. As to what...

Its realy nice indeed :D just a question, would it be and option to make a hole for the hammer adjuster and reg so you dont have to take it out to adjust? 😍

2250 2240 And this one. Adjusted the hammer spring and trigger pull.

Currently mulling over the differences between a normal Hammerli AP-20 and the AP-20 pro. Mainly I'm concerned about the polymer grip and the air tank. The grip seems to be sort of ambidextrous with additional plastic parts for a bottom shelf and where you're palm/wrist would be (sorry for the...

Thank you.

Check that the hammer spring tension is adjusted properly. If it is set too heavy, the gun will expel more air than necessary and be loud as a result. https://www.airgunnation.com/threads/average-fps.1296116/#post-1559114

Remove the hammer spring from Huma. That is too much. I tried it aswell, lightest Huma hammer and Huma spring and I was not able to adjust my hammer properly. Just use the lightest hammer from Huma, that is enough for 130 bar

Thanks Ok, Understand. If that is the case then I dont need to remove the screw because it's sliding fine and the wheel turns fine too. Did you mean to say the higher the number the less travel for the hammer? Because when the wheel is on MIN, the slider can move closest to the wheel and...

Anyone take their 22 call and make it a 177. Is there more than a barrel change required Presume the hammer spring pressure and perhaps the air valve to be adjusted

Nordicair, The clunk you hear when trying to shoot can be caused by a few items. 1. Hammer spring broken or insuffiecient to open valve. 2. Valve stem is sticking in the speed adjuster, (make sure speed adjuster moves freely and is opend all the way.) 3. Rear of poppet that acts as guide for...