Search results for query: *

It’s quite a few turns for not much change

I really felt like turning the LP up more did help. what is your HP set to? Before I recently did my transfer port modification my HP was at 2000psi and my LP was at 250ish and I was having really good luck 🤷‍♂️ I also could be Imagining things to lol

I have the Donnie FL Shogun that’s meant for a 30 caliber, but I also shoot it with my .177 and it’s very nice and backyard friendly. I’m shooting 13.34 grain 177 pellets so it’s pushing quite a bit of air and a .30 caliber moderator even on .177 works fantastic. I forgotten how loud one of the...

So around 7 mm That’s pretty large. I only went up to 3.5 mm/ 0.1377 and I was able to turn my regulator down by over 1000 psi.

So how large did you open up the transfer port seat?

So I was wondering where you actually put those. So my question is what’s the point of choking the transfer port back down vs just having the poppet seat smaller. Wouldn’t that defeat the purpose of drilling out the puppet seat? It looks like you, drilled yours a bit larger than I did. ?

So I just spoke with Scout this morning and they said that they used to lock tight the two sections together But eventually, the Loctite was failing so they replaced it with an O-ring. I did confirm that the O-ring size is a 1.5mm id I did source these ones on Amazon so I will see if this...

I think so! This could also be the cause of small leaks that people can’t find. And this is probably the cause of leaks when the gun is left pressured up to. yes the old softer O rings were also a cause but in the newer regulators they have all been swapped out to a 90 durometer which fixed...

Yes ! because that little ring isn’t doing his job, it leaks, causing air to push the large clear one off its seat and deforms it so it can’t seat properly. The reason the leaking stops when you take a shot is because it lowers that chamber pressure just enough that Air can’t push past that O ring

These things

lol 😂 OK, so I didn’t actually use pliers. They were flat faced things that kinda looked like channel locks. Not sure exactly what they were called 🤪🤦‍♂️ I called them pliers for lack of a better term But I’m sure a hardened, sewing needle through the small hole would probably work well

The flat side fits an Allen wrench The other side, I just had to grab with the pliers and be really gentle, and then it came unscrewed A sewing machine needle might be strong enough to put through that hole if you don’t want to use pliers

so my next thing is, I discovered a problem but it does have a fix, and it should be an easy fix as well. So I don’t know if any of you have had problems with airing up your gun in the air bleeding out spontaneously sometimes. I’ve had that problem on both of my guns. On my Evo, I replaced some...

Hey everybody, so this is gonna be a long post. Hope you don’t mind so I did two things today to Both my EVO and Epoch. so with the stock transfer port for .177 installed I have to turn the reg up to around 2000psi to push a 13.43g JSB redesign at around 720-730fps. so I decided to enlarge my...

Yes! got the non slip feet on. there are 3 sizes of cradles you can print. I printed the widest one so I can move the gun side to side a bit. we’ll see how it all works in the real world tomorrow when I go shoot

Just upgraded my 3D printer last week and just finished printing this! I really like how it turned out. Wish I was smart enough to design something like this, but I’m sure glad there are people that are So I can use their files they share.

Ok, ok …. Hold up! tell me about the grip you have on your Epoch !! I can’t stand the grip on mine. It sounds like a creaky door. the EVO is fine…. the Epoch… not so much. And that ajustable thing attached to the bottom ?

Interesting choice of design. from what I have read … so take this with a grain of salt…. baffles in firearms are different that in air rifles. In firearms, you’re dealing with hot burning gases and gunpowder that need to be stripped away as the bullet leaves. since the bullet is traveling...

I haven’t yet but I’ll share when I do

Thank you