EDgun Edgun Leshiy 2

Very interesting - so my set up is very similar except I have a 350mm 30cal barrel and a 0.1 and 0.2 jet - so I have essentially got 0.1mm more than you in jet size and 100mm less in barrel length and a larger / heavier projectile - I’m making 81ft/lb with 44.75gn hades and 82ft/lb with 50gn zan slugs - need to test more ammo - I seem to be able to get 2 mags at full power with a 350cc bottle which is curious

Main thing I’m trying to figure is if I can push any more power out of it
Wat regulator preasure are u running?
 
Very interesting - so my set up is very similar except I have a 350mm 30cal barrel and a 0.1 and 0.2 jet - so I have essentially got 0.1mm more than you in jet size and 100mm less in barrel length and a larger / heavier projectile - I’m making 81ft/lb with 44.75gn hades and 82ft/lb with 50gn zan slugs - need to test more ammo - I seem to be able to get 2 mags at full power with a 350cc bottle which is curious

Main thing I’m trying to figure is if I can push any more power out of it
Can someone tell me the overall length of the 137 cc plenum I can't find that info.
 
Wat regulator preasure are u running?
I don't know for sure. The 9mm plenum has a different location for the gauge and I can't get it to read properly. From the readings I've gotten, I would guess 185-195.

I found the sweet spot by cranking it all the way up and then turning down a quarter turn at a time until I got to a consistent 8 shot fps. Took a while as I was using a compressor.

Side note - if anyone shoots off a large bottle with an edgun, I would love to know the setup.
 
How to set your plenum air pressure via EdgunWest video. Shows what you need, where to put it, and how...

Oh, and you don't have to have the Meazy, but you will need the adapter and some other air gauge measuring the air pressure the way you want to see it.


I have tried this several times but no luck.

Is anyone shooting off a larger bottle with a whip connected?
 
I have tried this several times but no luck.

Is anyone shooting off a larger bottle with a whip connected?

It worked for me (I used the Meazy air gauge). My 9mm Leshiy2 was changed to .22 cal and I used the method in the video to step the reg pressure down to 105 bar. Which still gives me 760-780fps for the .22 cal pellets and helps quieten the bark (it's still a bit loud) so I can shoot in the backyard without alarming the neighbors. I'm still trying to make it more quiet so I'm talking to STO and hopefully they can assist in a solution.
 
Here's my setup for an Edgun L2 'Ultimate':

.25 caliber
470cc bottle
9mm plenum (Edgun.shop)
Jets: 0.2mm & Plug
Sub MOA Cut 450mm Barrel (Edgun West)
DonnyFL Ronin
Altaros ATP Smooth 50g

Over 100 ft/lbs, 8 full power shots per fill, ~991 fps.

Tested at 100 yards on 18 inch ballistic gel and went straight through. It will bring down anything at or under 100 yards.
I am curious why you went with the 9mm plenum? Do you feel like extra volume is necessary for extra power and, if so, what is the upper limit with the regular size plenum?
 
What bottle and setup are you using?

Usually this: https://www.airgunsource.ca/air-venturi-mini-wingman-100-cu-in-pcp-tank.html

I also have a bigger tank from the same company, but we usually get enough air from the smaller one.

My Leshiy is running a 22 barrel at 350mm length. I have a few other configurations for it, but they're all either .22 or .30 cal. At the range my son consumes about as many pellets as I can stuff into magazines, so it's .22 at the range.

Sometimes I've put the tank in a little sling I've made, and have the tank on my back. If I was going to spend an afternoon walking around a large property shooting at everything I see, that's how I'd go. But I find it's far more than I need for day to day pesting.
 
Last edited: