That does look high. I can get 86 fpe, JSB 50.1 at 875 fps with 135 bar on my .30 Delta Wolf in Factory mode.
Upvote 0
Daystate Daystate Delta Wolf..... A bargain of rifle?
- Thread starter Emu
- Start date
That is a really good question and something I‘ll check for. Hammer return spring is fine. leaning towards electrical issue since it resolves when allowed to sleep. Tried to recreate by waiting 1:28 and seeing if catching it before sleep was the issue.
Upvote 0
Huma regulator or is it the pressure transducer? I've noticed some variation in the pressure readings on the Delta Wolf which doesn't bother me, but show variation shot by shot. I set the regulator to 170bar which was very stable after the change and I assumed the pressure reading would remain at 170 shot after shot. What I've experienced after each shot is a reading as high as 174 to as low as 167. I haven't watched the LCD when i've fired the rifle but I assume the readout drops as the plenum empties and goes back to set point when the valve closes don't know what the refresh rate is on the readout but I'd assume it is many times a second and I'm also assuming the software takes multiple readings then averages them then displays the average. So whats the reason for the variation? Is it the error range in the Huma regulator (which I find hard to believe) or is it the error range of the transducer (which would seem excessive)? I don't believe the discrepancy has an impact on shot accuracy, but I'd like to know if the Huma regulator is causing that much variability refilling the plenum.
"Learning all the time".
"Learning all the time".
Last edited:
Upvote 0
I've owned 2 Red Wolves in the past, had zero issues and really liked the rifles. I'm currently looking at buying a .25cal Delta Wolf, but am now wondering if I should. First shot accuracy is important for the pest birds I'll be targeting at 80-100 yards.
Upvote 0
I paid extra money for having a computer inside the rifle.
I will not play the smart one searching a better option that the one the computer inside the rifle gives me as best setting.
If computer says: “regulator at 175 for those 950 fps with 44.7 pellets”, that will be.
Last edited:
Upvote 0
I have only had my DW since last Friday, but I have put a lot of slugs and pellets through it. I have only shot in advanced mode so I can't speak to factory mode, but I haven't had any trouble with 1st shot accuracy or consistency. I've only experience the variation in pressure readings noticed in my above post. So far the electronic components have worked quite well. The FPS of the pellets shot by shot has been consistently within +or- 1fps, really quite amazing.
Upvote 0
Yours must have been touched by the hand of God. I have had my reg everywhere from 78-170 and even on the low end was seeing a spread of +/- 18 fps.
Upvote 0
I set the regulator at 170 and haven't changed it since. Except for the small fluctuations in regulator pressure after each shot which seems a bit odd the shooting has been very consistent. Doomed JSB's 44.75 gr.
170bar/3250us/80V = 932fps
170bar/3000us/80v =929fps
170bar/2800us/80v = 926fps
I have shot almost the entire tin and the speeds are very consistent. I don't let the bottle go below 200bar and I swapped out the 480cc for a 700cc bottle.
Just curious have you tried warp mode?
Upvote 0
I haven't. Picked up the DW to eliminate the need for multiple air rifles via the profiles for various pellets. Was surprised to see that even low reg pressures have pretty much no change in fps spread.
Upvote 0
Where can i find factory setting in advance mode? Please teach me too
My gun shoots kings in one hole but exactly at 900fps. How to ffind which settings is my gun using for that speed?
Upvote 0
Got a video of the fps issue. This profile is set to shoot Barracuda Hunters at 845 fps. The profile is randomly being locked at a lower fps until the rifle is shut down and booted back up.
Last edited:
Upvote 0
There you go now there’s someone that thinks like me. Do I want to spend a whole weekend tuning? f no. This is the answer
Upvote 0
That's very strange. Do you get the same results with JSB pellets? Is it like the Ghost and single loaded pellets could inadvertently fall into the action?
Upvote 0
I don't shoot many JSB these days, although I don't believe it to be a pellet issue but rather electrical. There is a noticeable POI change, but they group fine enough at the lower pressure.
Upvote 0
If all the connections are well seated and it is doing that I would send it in for warranty repair.
Upvote 0
AOA is checking with Daystate to see if they have direction as this is the first time they have seen it. Will update as I hear more.
Upvote 0