Recent content by robertwalsh1981

BRK Ghost .22 HP 23" Barrel Reg = 110 BAR (Digital Gauge) White hammer spring ================================== JSB Hades Monster 25.39 gr PW=MAX 881 FPS avg. Shot count: 5 Low: 880 Hi: 881 Avg: 881 STD Dev: 0 Spread: 1 4/20/25 7:45:41 PM,881,FPS,43.8,FT Lbs, 4/20/25 7:45:46...

I ended up just ordering a DOWTY SEAL kit similar to this one for my BRK Ghost except mine was for bsp thread, and the avenge-x looks to use M8 thread. I ended up with TONs of sizes I don't need but trying to order the specific size I needed was going to cost more for one than I paid for the...

Cool thank you, I have watched that video a few times unfortunately they already have the knob off and don't make mention of how it comes off. I appreciate the insight to look for an Allen set screw vs my just trying to back it out and then messing up my reg! Also, not sure why checking the...

Question for you, I am getting ready to take the reg out of my Ghost HP, when you took yours out did you just unthread the regulator adjustment knob (counter clockwise) until it came off to allow access to the regulator for removal?

Honestly I am loving mine (even with the hiccup) and can't wait to get it dialed in!

It doesn't sound like it is very common but I thought it might be worth sharing what was happening and a summary of the solution incase someone else ever runs across it. :::::Issue::::: A few days ago my new Ghost suddenly stopped producing power it would shoot but instead of getting ~850 - 900...

Yeah, going to have to degas the gun again to get the reg down a bit and see how they do. Ideally I want to see if I can get it dialed into a tune like the one HERE ====== .22 HP 23 inch barrel, reg 152ish (damn baby gauges…), blue spring: AEA 25.3gr at 950fps on PW 16 AEA 21.9gr at 915fps on...

With a bunch of elbow grease and about an hours worth of threading the stem pieces back and forth/back and forth, I was able to get them seated. They now have a dose of Loctite (I only had the blue, but it is better than nothing) and the gun is reassembled. I took it out right at dark to confirm...

Yeah, I have reached out to Tony at Talon Airguns to see what the process for a warranty claim looks like. The complete valve is ~$150 from AOA so if the warranty doesn't work out I will be digging online in search of a replacement stem.

Yeah, I cleaning the male threads with a brass wire brush, but it isn't wanting to thread in any further. It acts like the threads are galled. So I am going through my tap/die set to see if I have anything that matches the threads in hopes of cleaning them up (gently) by hand.

I was able to get the valve out and it definitely looks different than what is in the BRK strip down video. (I know there have been some changes) From the video: Pulled from my gun: The internal end of the Valve Pin appears to have backed out with only a few threads holding it. Also by hand...

Forking this slightly, if the reg was damaged when I adjusted it down while under pressure, would it require replacement or just rebuilding the o-rings?

Yeah, my valve is not moving at all via hand pressure and if it moved when I was tapping it with the hammer I couldn't see it. That along with the fact that I am seeing increases in FPS when installing stronger springs would seem to indicate the issue may be in the valve. I appreciate the info...

Ironically I just finished reading one of the threads that discussed the hammer getting bound up. After reading your comment above I went and verified that with the Blue spring and the PW set MIN I can hear the hammer sliding freely when I tip the gun forward/backward. I did verify that the...

I was dry firing as that was how it was shown in the BRK tutorial videos, I have been degassing via loosening the reg gauge since the issue as dry firing would take a crazy number of shots (probably more than 20)