Recent content by mtm100

My math lead me to the same thinking. But that is still way off. OK’s method of 3 moa per line is spot on for my holdover. My holdover for 10 yds is just over 2 lines. 7.1 moa would equal about 2.3 lines. I expected the program to solve for this. Knowing the reticle and the magnification setting...

Holy Crap, I think this is just the info I needed. So each line in the reticle is marked 2 MOA on the spec sheet. So the first line says 2 the second says 4 and so on all the way down. Chairgun Elite says I should hold U7.1. Where is that on my reticle? Thanks so much for your help.

Holdovers for Hunter FT

Good Morning, I'm wondering if anyone is getting usable results from any Ballistics program to set up a FT scope wheel? I've been using these programs on and off for years now. The only one I got usable results from was the old Hawke Chair Gun Pro for Hawke scopes. I'm now shooting a Sightron...

While I kind of agree. Fx liners are rolled on the outside to make the rifling. Cut rifling can be rough from the transition lands to grooves. That’s all your soothing out by polishing. The inside of a fx liner should already be smooth as no machining has been done on the bore of the liner. I...

My guess would be no. I've only had luck polishing known good barrels that have degraded over time. Lapping might fix it but it's very hard to do. Can't hurt to try. JB bore paste only. I've had bad luck over polishing with Flitz. The bore gest so smooth the pellet slows down a lot and it leads...

Well I think I figured it out. It’s the fx barrel as suspected. I just finished adapting a Walther poly barrel to the king. Now shoots typical match scores. Dropped 2 points out of 60 at 25 yards. That’s pellets right out of the tin. I pushed a few pellets thru the STX liner and it had several...

Hi just a little update. I called tech support at Utah air for some advice. They were very helpful. Long story short. The king and like guns were designed for high power shooting large calibers. We all knew that. Not much info on the low power sub 12 ftlb guns sold in Europe. The transfer port...

Thanks for the replies. I build and service a lot of high end guns. And yes a poly barrel shooting 13.43 around 800 FPS should shoot well all day long. I tune many Thomas's and Raws to this spec and they all shoot very well. I picked this King on a whim. I shoot a lot of bench rest and Field...

Hard to believe a $2300 gun out of the box can’t shoot a 1” group at 25 yds.

Thank you. Are you shooting pellets or slugs? I need to shot pellets at or just below 20 ftlb.

Hi, I just bought a new FX King 177 with the 500mm barrel. I'm wondering if anyone has got this arrangement to shoot very well? I was hoping to use it as a loaner for Field Target and Bench Rest shooting. No decent results so far. Do they all shoot this bad? Thanks, Mark

Hi. I started at 20 yds and the shooters liked it better. Why not higher scores make everyone feel better. The challenge is shots need to be kept in the 2” target square for clear scoring. At 25 yds most good shooters can keep it in the target box. New shooters may have trouble at 25 yds so I...

Greetings, I have a few USARB announcements. 1st, I have taken over target sales after Joe Fredrick did a fantastic job for so many years. Thanks Joe! Target costs and shipping has increased a fair amount. Should be no surprise there, we haven't had target's printed in several...

Hi Guys I just came across this thread. Thanks for the kind words. I’m happy to share what I’ve learned over the years. But those of you that know Mike will notice I mimic most everything he says. He and I go way back and has shared lots of info over the years. No secret I’m a big Thomas guy. I...