Recent content by mattboyer30

So I finally took the dive and used some of my experience upgrading my Notos and took this one apart, assuming that the "power kit" supplied was to replace something restrictive deep down in the gun, which was the case. There was what looked to be a regulator, just like the Notos' one, very hard...

Where is the adjustment for the semi-auto? I just got the max, and cannot figure out how to achieve it. It came with the "power kit" piece, which I can't find any info as to where it goes or how to install. Only instructional I've seen was one they sent where it's removing the 6mm plug and...

I could swear I've seen fill whips that don't have the "spring" on the outer, but can't seem to find one anywhere I've looked. I completely understand the purpose of them, but assumed the ones I'd seen maybe were reinforced internally to keep from kinking, just a guess. It'd be a nice thing to...

It's definitely a pull when on semi-auto especially, 5oz would be less than a feather pull - so 5#...I'd even venture to creep that up a little when in semi-auto mode - still though, no worries, I got used to it and am hole in hole at 40 yards every time after a good tuning & some experimenting...

No I sure haven't...I'd do this..Go to DonnyFL site and do the "contact us' and get that insider info. It could be one of those things that's "here in the US, but not in UK" or vice versa...Prime example is the anti-cant bubble level at the edge of the pic rail (closest to your eye) built in...

Last month I got the .25 standard...Absolutely awesome....I haven't been able to really shoot a whole lot, a couple of clips a day, just sooo cold out & am actually asking out if anyone knows the degree to which freezing temps affect POI? I can't imagine it doesn't to at least some degree, if...

Ah funny you ask...I'd went with the 380mm c88 shroud & FX superior liner, and sighted in after getting that all put in. At that point the scope was about mid-way of its adjustments & pretty much zeroed. The shroud had a minor issue from the start - the indent that takes the grub screw was maybe...

Dang thanks so much for the summary. I'll work with that approach. I'd definitely gotten the reg out of whack. I did read the CW / CCW rule on the site I got the new block from, at the moment I'm still with the stock reg that requires degassing, taking the tank apart, reg pulled out & adjust. I...

Yep I did. Being an amateur, when I took things apart to oil & clean I'd also intended to set the reg & hammer spring back to factory and start working back up now that I have a chrony & find the sweet spot where my FPS maxed out so i wasn't just wasting air opening up too much. - a little more...

Ohhh yes FPS I'd been reading on FPE last few days & stuck in my head lol - thanks for the correction. That explanation sounds to make a lot of sense...What would the fix for that be then? Less/more hammer spring? Or cut back on the regulator a bit?

Hey everyone - I've made some progress on my Notos so far, upgrading to FX 380mm barrel & CF shroud from c88, UTG BugBuster scope, polished some internals, etc... - I recently put everything back together after some deep cleaning & attempting to change out the poppet valve with an MCP...

Definitely will do. Thanks man look forward to it!

Hi there! I have a question on a couple of your mods I haven't seen or where to find them...The middle one and up, that cocking lever mod - I've seen FX guns use that & seems its a really smooth minimal resistance cocking lever setup? How does that work, what would you call the parts if trying...

Ah understood - Appreciate the insight!

I have a question on the eye relief on the Notos...BTW I did get the 380mm barrel & FX liner on & plenum extension - so far noticeable improvement! I get the buck rail suppressor today - it was a bit noisy for the back yard without one lol. - The eye relief- -So, the scope in my pic, I wound up...