Tervang23 said:

Looking for anyone or any shops around the Fresno Central Valley area here in California who does services and can help me install some accessories on my impact m3

Click to expand...

Fx impact m3 .25 bronze for sale: still available?​

This listing has been renewed

dgeesaman said:

I have a barrel of particular interest that was machined for a clamp-style receiver at 16mm. It was not machined well and this surface is wavy and inconsistent by a couple thou.

I’d like to put this barrel in my RAW which needs to be .625 (+0/-.0005) diameter. So I assume the only good solution that keeps the length is to OD grind down to .625 and hope for 90-95% cleanup. (To be clear I only want the receiver end ground - not the whole length)

Suggestions who can do this? The local machine shops might but they aren’t barrel people. Bonus if they can machine the port and chamber too.

Click to expand...

A manual machine job shop can easily do this. You have all the right call outs with dim and tolerance.

This listing has been renewed

This listing has been renewed

This listing has been renewed

@Mark B - Please interpret: HPA-SSP-MPP

HPA = High Pressure Air = PCPs.

SSP = Single Stroke Pneumatic = Pistols and rifles that are one cock, one shot with an air resovoir.

The P17 is an excellent example, everyone should have one. Very affordable SSP pistol with an amazingly good trigger. Direct copy of the much more expensive HW40A.

MPP = Multi-pump pneumatics = Sheridan Streaks / Crosman 760

crowski said:

I had the Lazer and lens put in eyes last year. Don’t wear glasses any more.
The sights are what came on and not sure if correct.
The 601 was shooting so low.
I haven’t bought a gas can in 20+ years. Bought one last month and the 601 shot so low I hit my new gas can. View attachment 583742PMO. My mistake. Shot 10 inches low. Not the greatest target holder. 10 meters.
These guns are the best. Crow

Click to expand...

You probably know this , but a little 2 part epoxy fix that gas can hole.

I know the problem, your hammer adjuster is loose. There is a small grub screw on top just before your stock attachment, the center one. It controls the spring and bb that notches into your hammer adjuster. When you shoot, it starts backing out and loses tension on the hammer adjuster allowing it to spin with every successive shot. You need to snug it up, not too much as you don’t want to crush the spring, get your hammer adjusted where you want it, then back out the grub screw and add either vibra tite or blue loctite just a tiny bit and screw back in snug. That should keep things in place.

Funny you should ask. YESTERDAY I was hunting with my Edgun R3 long,.22 slugger. I realized I had a tin of those that Centercut gave me a few weeks back so I tried them out (25.39gr?) Holy crap! They were shooting as straight & accurate as the preferred slugs that the Edgun LOVES (.217 Daystate Howlers or NSA .217)! Also tried Hades & Redesigned Monsters, they were OK but couldn't come close to the Center Punch!!! I was amazed at the accuracy & consistency. They shot as accurately as slugs and out to 125 yards! I'll try longer range next time.

Yes. My China clone is electric but looking at ops Pic it's a 1:1 I had to re tune the safety blow off valve and the auto stop to change mine from 3000 to 4500 fills. A matter of an Allen wrench for the auto stop and 2 wrenches for the blow off safety

crowski said:

Thanks. The 601 front sight was missing. Oddly there was a front sight on my kitchen floor. No idea where it came from and used it. I have several Weihrauch front sight sets. Will they work?
Not at all familiar with these guns. Crow

Click to expand...

Weihrauch inserts will not work in that sight. That sight requires the use of inserts that fit an 18mm FWB front sight. The HW inserts are 14.6mm.
Looking closely at the picture you posted, it appears that the ears of the insert are not fully seated in the front globe causing the insert to be positioned high of center in the front sight possibly?

manabeknives said:

it's an older picture that has not been updated with the current revisions

Click to expand...

Typical, so why don't they update their website?
Been though my HP reg again, and it's fine cannot find any reason for the slight drop in power, but as per usual as soon as I start working on it, first the bleed valve starts to leak and the bottle valve O ring goes, I then took the spool valve apart and enlarged the closing jet, but once all back together the only difference I can see is now the LP reg pressure has risen from 150psi to 165psi and I detect no change in the firing note that Motorhead described, and no change in constancy these guns just seem very unpredictable it can be good and consistent one minute and jumping about the next O well back to the drawing board, perhaps my quest for single figure FPS is just a dream with this gun.

I mean, you put that on a Micro then play with balance and find the sweet spot, that may work, no?

Adjusting regulator to increase counterclockwise or clockwise?

Don't some red dots attach directly to the slide of a say glocks? I'm sure they'd handle an airgun.

I was giving the PCP guys a run for their money with my HW97k .20 this weekend at 55 yards. They had the advantage at 80 but I was still hitting cans and the big spinners. Not too bad for a lowly springer.

Will it fill SCBA tanks (4500 lbs)? Scuba tanks (hp) are around 3200ish lbs. For airgunning 4500 lbs is needed generally speaking.

Im also having sort of a garage sale

6 Inches is plenty for a rest bag to be attached. So I guess that's a yes.

I have one left

Tricky-Dicky said:

But it only seems to exist on the epoch reg and the screw on cap seems looks shorter.
Took my HP reg apart to clean up and check last night and didn't notice any part like you're describing?

Click to expand...

it's an older picture that has not been updated with the current revisions

Us forum dwelling air gunners are but a mere drop in the bucket of the total number of uninformed folks out there that just shop and buy at the big box stores. Like mentioned before... Walmart market.