Folks have been putting food on the table for many, many years using lead. I would bet that there is way more risk of dying in a car crash.. but that don't stop us from driving them. Gotta get there and ya gotta eat.
I would venture a guess that there are alot worse things that we let into our bodies and just don't think about.

I have the Xisico version of the CS3e and I'm very happy with it after 2+ years since getting slightly used for a couple hundred bucks. I've done general maintenance twice since I got it following instructions from Target Forge. I use food grade green grease.
I only fill guns directly with it and have a Yong Heng to top off my tanks. Both compressors have severed me well.

delooper said:

I probably went overboard buying pellets early in my PCP-era. I wanted to try every varety, and if you look long enough you realize, there's a lot of varieties out there.

Click to expand...

It only gets better…. Define better ahead of time

Normkel said:

The owner's manual Page 2 under Directions for use: 1. Machine test, Attention: <cuation symbol> 1. Note - describes adjusting the "Safety Valve"

This video shows how to adjust: https://www.bing.com/videos/rivervi...B3C0975A101DF9370B60B3C0975A101DF&FORM=VAMGZC

Click to expand...

Awesome! Thank You for this

My leak turned out to be the fill nipple as I had removed it to check the valve and O ring it was not sealing around the thread, so some more PTFE tape and it's fine again, using a bit of washing up liquid in water and a fine brush is good for locating external leaks.

Bramezy said:

So Ive emailed and called RAW, been waiting days for a return email or call. Kinda sucky.

I just need some ideas.
Micro, HM1000 acts like its not regulated in the sense of I can adjust the hammer spring, get two to three shots consistent then it starts to climb in velocity. Ill readjust and repeat this process over and over. Ive put new orings on the reg and cleaned up the bellville washers and same result.
Ideas on what to check?
Ill fill to 200bar and run it down to 150. Ive wasted one crap ton of pellets chasing this thing.

Click to expand...

is this a brand new rifle?

New Tuxing 6.8L tank did finally arrive yesterday.
There was also two small spot at aluminum internal liner.
It was only possible to see them with endoscope.

Otherwise i was nice one.
I had to take it and hope it will last long time to use.

I probably went overboard buying pellets early in my PCP-era. I wanted to try every varety, and if you look long enough you realize, there's a lot of varieties out there.

marflow 777 said:

got some butt spacer and they don't fit the plastic stock at all too small

Click to expand...

Do you get a new sear with the bolt kit?
There are spacers available for the synthetic stock. And they perfectly. Item number 138420-000

Climber said:

No one warned me this was hobby was so addictive and the bunny hole is deep enough to not have a bottom.

Click to expand...

Chris,

you're already learning some of the great thruths thay bind us all.

Yes, the airgunning "bunny hole" you call this so endearingly is indeed of surprising depth and width!

Here's a photo to appreciate its dimensions:




Congratulations on your excellent progress on your way down there.

Some people start with climbing down the airgunning hole, others slide into it — you however have achieved an early free-fall.
Just wait till you reach terminal velocity. It's fun!!

Matthias

Revoman said:

Trying to skirt the rules, huh. That's not a good way to start making friends on any Forum.

Click to expand...

didnt ask, wasnt selling it, just was talking about my gun and whats on it.

Thanks for the input Marflow - I have neither the 5-shot clip nor the single-tray. Too bad Magic could not continue to offer the copies along with a liability disclaimer (or similar) to be signed by the buyer to relieve Magic from any and all liability; I know I would readily sign such a form.

So, from what I understand, I am dead in the water ... or at least the B96 is. lol.

Biggest problem with non lrf in my mind would be night hunting. If you are going to night hunt at unknown distances it will be much more difficult. During the day it’s a sweet feature to have but you can always still use a regular range finder and just hold over in the reticle.

+Your first PCP is a great start, easy enough to hand pump, it can shoot pretty accurately,if you buy another PCP without thinking, you would be a da.Use what you have until you settle down...... There are so many choices, plus different calibers...think and plan,study and become informed.In the meantime save your money..................for your informed choices.

What did not being able to use the app limit ?

A very old thread, it was fun to read through it again.

I'm still enjoying the heck out of my Shorty Veteran. It's still a .20, and still in the aluminum chassis stock, but I changed out the grip. Here is what's on it now.



Took a bit of Dremel'ing to get a non flat top AR grip to fit where a flat top is intended, but it worked. I tried once before and ended up ruining that particular grip. Learned some lessons from that and was successful in this attempt.

Decided the gun just needed used after the grip upgrade, so took it with me to kill time during my son's soccer practice. Dropped him off and headed to a dog town....killed 11 with this gun, out to about 70 yards.

Had some exceptional conditions right before dark and decided to shoot some groups on paper at 55 yards. This is from stool and sticks. .20/13.73 @ 805fps.

Five shots...


Yep, impressively accurate little gun. It's had a lot fo shots down the pipe, and will have many more in the future. I REALLY enjoy this one.

This listing has been renewed

This listing has been renewed

Here is the needed folder with all the files.

View attachment winGCU-0.3(1).zip

Some kind of rivets. I drilled and ground them off. Never plan on using that cord reel again. In the trash it went!

A regulator doesn't close when the tube/bottle pressure falls below the reg set pressure...so tube press=plenum press in that case

Maybe the former owner turned the set pressure all the way up to the 200 bar ?
Thinking to actieve max power by doing that?
(A lot of People seem to have not a clue what they are doing)

small change that someone woud do this this or if it's even possible to set it to 200 bar ...but you never know and would be worth a try to lower the set pressure before ordering new stuff
by the way these New amp regs are just fine ( i own a crown and adreamline) . No creep at all

Pale_Rider said:

MacTen: Why don’t you go start a Huben thread. I started this thread as a taipan slash thread

(2 posts later)

Diago: how about AEA challenger pro?

Click to expand...

Airforce texan?

kaylaindy said:

I do have 6

I actually do have about 60 guns. Those were the only ones I could fit in that cabinet. I still have piles of guns in boxes. But I do sell most of them which is why I only have 60. Rick Rehm Shooter 1721 had 280 guns, 2 years ago. He probably has about 350 now. In about 3 weeks I can do another Slash video and shoot it properly at 50-100 yards.

Click to expand...

Def can’t wait for that. This video honestly was yeeeah…everything shoots well under 40 yards. Looking forward to it getting stretched out.