Theoben rammers, vet1’s and Huben’s . Good for what I do hunt and pest.

Is "the big auction site" what we call the thing that starts with e? Lol. I'd be interested on other people's thoughts here as a newbie. There were two other listings recently with still semi-reasonable prices (700-800) + some stuff thrown in but it looks like they're gone now. In fact one of them was just snagged this morning it seems.

Not too much different really. I started with a Crosman 180, then found a Sheridan blue streak. I've never ventured all that far away from those. Ended up happy with the QB77 and QB78 series rifles.

HPA has just never appealed to me and neither have springers.

Cheers,

J~

beerthief said:

please tell me you were shooting inside with no fan .

Click to expand...

I was shooting indoors and you better believe I had a fan directly on me. It was 100 degrees in there!

Lewis said:

ZOINKS!!
That is amazing.
How is the BC? If they can handle the wind, it looks like a great contender for RMAC.EBR,PA CUP etc.

Click to expand...

The screenshot shows you the BC. The video shows a typical RMAC style target at 100yd in a mildly variable wind condition.

I am not sure what he does. It still gets a metal butt plate . And the final finish.

marflow 777 said:

they look like Phillips screws but they are not
for any of us that has tried to remove a Diana scope mount----ME----you just screw up the screw top
the gun would have to be taken apart as far as i know to get to the back of the rivet and then what spin the back of the screw rivet
now this is a 48-52 tube and what you are looking at is the rear most screw end at the right and a locator pin that is on the mount
you can see that the screw has been worked over to peen it
and every screw has access though the tube
now i would assume your is similar
View attachment 582814

Click to expand...

Reread your post and thought it though. suspect careful work with a punch may work

the question asked," are glass optics becoming obsolete" No!, they never will be obsolete in my lifetime, nor will be a Burrito.

Blue Thread Locker

yes i know the set up yet has any one ever fixed it ?

This listing has been renewed

This listing has been renewed

This listing has been renewed

This listing has been renewed

This listing has been renewed

This listing has been renewed

dk-duck said:

hi thank you for getting back to me, and yes it came with a factory regulator new, the only problem is we asked huma-air to set it for me at 12 lb which they never, we still don't know if it need's to be sorted out before it goes into the air cylinder, because you're meant to screw it at the top then underneath thank you

Click to expand...

no what happened is I got into the hobby after having an illness I went to the local gun club, after being there a while I asked if I could buy the artemis p15 from him, we've recently found out the spring had been swapped to an even smaller one, i had to give him the rifle at that point because I didn't know how to change the o ring's for it, long story short the rifle was given to him to replace the o ring's all of them had to be done apparently when he had the rifle he said that he had put the rifle to 11.28 energy foot-lbs but we only recently found out that there are o ring's missing screws too short or not there, basically the rifle seems to of been thrown together wxxxxxs!! we noticed the spring is so small it's not even the correct size for any of the spring's for the artemis p15, I swear talk about having you're pants pulled down or what, but there's you're answer buddy... no. I'm currently looking for a spring and everywhere seems to be sold out lol thank's anyway

This listing has been renewed

oaks1450 said:

Bottom right looks real good. Any chance you’re going to Nationals? I just signed up yesterday.

Click to expand...

No, I'm mostly just a local monthly match sort of ft competitor. Still got young kids at home and full time job. At this stage of life I just don't have the time or interest in traveling to chase GP points.

DesertSilver said:

Remember, the hammer spring tension needs to be strong enough to open the poppet valve. The higher the reg setting the more tension is needed. It's a balance.

Click to expand...

thank you for your help and advise how many turns does the huma regulator need we've been told 2 then 3 we aren't sure tbh if you could give me some advice there please I'd appreciate it

OldVet said:

I used the metal pp750 baffles I accidentally got from Wes at AAF , And put them in my tactical Gauntlet SL 22. There metal , fit better have a smaller hole work better. I also put some clear plastic tubing on the Gauntlet barrel. Much more Quiet now. OV.

Click to expand...

Nice. Let me know if you ever need some more. I took the shroud off and use an adapter.