Parting ways with items I've accumulated and don't use. Older Air Wolf PCP CDT. Has electronic trigger but no digital display. Excellent condition. 

$700 plus shipping costs. Pics available as requested. Includes approx 1500 Diablo exact pellets. Someone can put this to more use than I did.

Decided that my RAW HM1000x 25 is a bit too loud for my range and reluctantly selling it. Gun has new poly barrel with UNF threads and CF shroud installed and tuned by Martin. Action is left-handed which is actually easier for right handers but interferes with large scope wheels. Right hand stock! Pre-Airforce gun with narrower magazines, three mags included. Superior wood, fully adjustable stock. Clean and consistent. Shots around 850 fps ~ 34g JSB

$1600 plus $50-$75 (from 14559, Rochester, NY) double boxed shipping

Accessories I will consider selling for additional with this gun, not available otherwise (may list after gun sells)

Nightforce NX8 4-32x50 FFP Mil XT 

FX Adjustable Rings

Hoptic Scope level

.25 pellets including JSB/FX 34g

Donny FL Emperor v3 2x10.5 22-25-30

RAW Anschutz to Picatinny adaptor

Atlas BiPod with Picatinny quick release clamp

Complete package $3600 (do the math, it's a good deal) can add a Hill Compressor for $1000 more

Please no offers or trades I will not respond

I have lots of feedback I can send, infamous on all the forums ;-p Thank you, Frank P

 ***SPF***Burris DropTine .22lr 3-9X40 Ballistic Plex. Life time warranty. This is
New in the factory shrunk wrapped box. $110.00 SHIPPED

Nikon Prostaff 2-7X32 Duplex reticle as new. $120.00 SHIPPED

Airbow in Excellent condition with 1/2 dozen new arrows and 5 more like new. Comes with Quiver, Centerpoint scope and mounts. and fill probe.

New the Airbow cost $949 at PYA but on back order. Arrows are 112.99 a half dozen. I am asking $600 for the Everything and I paid extra $200 for the scope and quiver.

A Trooper618 was interested but I his messages disappeared on the forum for some reason and I had some pics for him which I will enclose below.

E-mail me if interested and no Low Ballers please E-mail me dayjd at sacoriver.net I accept PayPal + their 3% Fee. 

NOTA benchrest – hard to come by and $$$$

I bought it and then the BR group at the range fell apart so I have no use for it.



TRADES:

TX200 – prefer a custom stock, something cool in laminate or walnut perhaps? Mk1 and Mk2 preferred – HC or full length ok – Maccari or Watts customs

HW95/R9 – as above – custom stocks preferred – Maccari or Watts custom

Prefer PayPal FF for payment – would also accept Venmo and money orders if required

I have years of feedback on the old Yellow Forum and bought and sold here too

Thomas .177 12fpe in FT stock ($3800 new and 6+ months wait) – one hole shooter as you'd expect. Built, assembled and tested by Mike personally. Shot 3x at the range and few backyard sessions.

TRADES for partial:

TX200 – prefer a custom stock, something cool in laminate or walnut perhaps? Mk1 and Mk2 preferred – HC or full length ok – Maccari or Watts customs

HW95/R9 – as above – custom stocks preferred – Maccari or Watts customs

Prefer PayPal FF for payment – would also accept Venmo and money orders if required. I have years of feedback on the old Yellow Forum and bought and sold here too

A great seller. Willing to answer my uninformed questions. Prompt shipper

new tanto 75 shiped i have picts up soon had to open it up on inside to get it to fit longer threads 

15 different tins of pellets. These are pellets I’ve tried in my springers when testing to see which pellets they liked best. Be a perfect assortment for someone wanting to test them in there pellet gun. Some of the tins only have 50 or so in them but most are near full. 


Sold Pending Funds


$70 shipped CONUS OBO 

I purchased a barrel from Robert. No issues, good communication and shipped fast. I would purchase from him again.

$30.00 each + 12.00 shipping, spacers not included.

$52.00 each + 12.00 shipping with custom spacers and o-rings for FX Crown.

In order to test the OD dimensions for for CF Barrel Sleeve / Shroud spacers (https://www.airgunnation.com/topic/wts-fx-crown-mkii-spacers-for-cf-barrel-sleeve-shroud-now-in-yellow-blue-black/) I did not already have, I bought these barrel sleeves for measuring OD. Otherwise they are new and unused condition, other than a single measurement.

You can combine with the CF Barrel Sleeve / Shroud spacers in my other add and save $4.80 on shipping.

To see more about the spacers, please see: https://www.airgunnation.com/topic/wts-fx-crown-mkii-spacers-for-cf-barrel-sleeve-shroud-now-in-yellow-blue-black/

60 minutes scuba carbon fiber tank manufactured 04/01 last hydro in 2015 if you have a compressor this will work for you 225 we split the shipping PayPal for payment 

I designed and printed some of these V2 spacers for my FX Crown MKII after I couldn't get danny5692’s design to print well (edit: This design https://www.airgunnation.com/topic/carbon-sleeve-fx-crown/#post-1164001).

My V1 spacer design was a short spacer height, and did not have enough friction between the CF barrel sleeve. So I hit the drawing board, and without further ado, the new and improved taller spacers:

The purpose of these spacers is to center the barrel within the FX Crown shroud, which I found essential if you use a moderator. These spacers work for the .177, .22, .25 and .30 CF sleeves, and fit between the FX CF barrel sleeve and the FX crown shroud. The CF barrel sleeve stiffens the barrel, but without these spacers, the barrel and CF sleeve are not held fixed to the shroud.

UPDATE: The cost is $20.00 for a set of three five-spoke spacers with o-rings. The cost is $22 for a set of 3 spacers with o-rings. 

This new improved V2 design takes longer to print, but I've lowered the cost down to $22 for three spacers and three o-rings.









The next photo the spacing is not correct, it is more to show all three colors in the same photo:



When installing the FX Barrel sleeve on the FX Crown barrel, you may decide to use electrical tape to affix the CF barrel sleeve to the barrel, or use Teflon, or to epoxy it to the barrel. I ultimately decided to use epoxy (Infinity Bond EP 420 High Peel and Shear Strength Epoxy - 25 Minute Open Time) as it is slow curing...I waited a day before I installed the spacers and shroud. However, this is a rather permanent solution so I would try it with Teflon or electrical tape first.



Comes with written instructions and a 30-day money back return policy.

Shipping is $4.80 USPS First class with tracking, or a faster $9.85 USPS priority mail to continental U.S.

I made another batch. 

These blowback shroud to use the space behind the Leshiy 2 barrel muzzle as blowback expansion chamber. Works with Huma-air Mod 40, DonnyFl’s Sumo, Tatsu, Shogun or the new Fatboy 2.0 moderator. The shroud screws directly to the barrel and goes inside the CF handguard. Works with 350 or 450mm barrel. 

price is $60 each for 350mm barrel version or $75 for 450mm / Fatboy 2.0 version. 

PayPal F&F or please add 3.5% and I will cover shipping to all 50 states. 



With the Sumo

With the Tatsu 


With the Huma-Air Mod 40




Here is a video from AGN member J Wilson demonstrating the shroud in action. 
https://youtu.be/Czf_W8xuPq4

I have a Vulcan 3 in .22 cal 700 mm. Shot very little. Still looks new. Will come with all the things that AGT ships it with. Has 3 mags. I’m the original owner. Just not a big fan of .22 cal. Looking to get 1400.00 obo plus shipping. PayPal f and f or add for fees. Respond here or txt/call. If I don’t answer txt or call me back. 731- 609-1933. Also can email at [email protected]. Can send pics upon request. Thanks 

No more worrying about snapping magazine holder O-ring on your Leshiy 2 magazine holder. This magazine holder stores your extra Leshiy 2 magazine right under the scope rail with a strong N52 grade magnet. The magnet has over 3 lbs of pull force. The magazine holder can be installed in under 5 minutes.

See video for details.

$20 each. Shipping to USA included 

PayPal F&F or add 3.5% for fees

PM or email me if interested

[email protected]





https://youtu.be/uUknCZOsDI8

Quick to respond and helpful to an older (83) seller! Very nice transaction.

used bully for sale 550$ its a 45 cal

Crawford & Luft R hand adj riser excellent cond I think this is the first version. Asking $45 PPFF Cont us

Nice transaction, fair dealer. No BS seller.

FX factory carbon fiber tuner for either 22 to 25 or 30 caliber excellent condition in factory shipping tube. Ship Cont.US PPFF $140

 

I used this mount for my pard 008 LRF but sold my pard so no longer needed. You can use it for a rifle scope or a pard. Unlimited functions mounts to your rail. $95 shipped PayPal F&F.



Main benefits of using this mount:

1. NV scope:
It can be directly fitted to the Pard 008 008P 008LRF

2. Adjustability:
FULLY ADJUSTABLE, FORWARD or BACKWARD , ELEVATION, WINDAGE, EYE RELIEF AND HEIGHT ADJUSTMENT, that allows the scope to move vertically and horizontally along a guided path, and lockable in different positions, using 3x or 4x or 5x screws on the side of this mount.

3. Combined with Scope cam:
This mount allows users to adjust their scope forward, backwards, or adjust it vertically to align the scope with their eye relief or eye level.
Users wishing to use their scope camera and record a session while shouldering their rifle, but the screen needs to be further to their eyes, or, for some applications they might require the camera to be closer to the eyes, such as pard/ Nightvision scopes etc.

4. longer range shooting:
long range before running out of adjustment on the turrets
is the ability for users who need to reach out further but are restricted by their current mounting system.
By keeping the front mount at it’s lowest and elevating the rear mount to the highest point you can zero in your gun far beyond, without using the clicks on your turrets, hence keeping the optical centre of your scope intact.

5. Multiple rifles:
This system can be used to install scope mounts for the owner’s of multiple rifles who require to use one scope for all of their rigs by installing one Infinity mount to each rifle.
They can zero then just swap the scope between them, with little need for turret click adjustment.

6. Durability:
This product is robust enough to be installed on heavy recoil rifles, up to .308 caliber.

Paid quickly and was very responsive to all communication. An exemplary AGN member!