Barrels NLA .35 cal. 800mm FX Impact STX Tensioned Slug Barrel Kit
- By chuckster636
- Member Classifieds
- 0 Replies
Today I am selling my used .35 cal. 800mm FX Impact STX Tensioned Slug Barrel Kit, which includes the fully assembled barrel with barrel clamp, carbon fiber sleeve, and Huma Dual Ported Transfer Port & Pin Probe installed. Also included is a Huma .35 cal. pellet probe, a Huma 56mm High Power Hammer Spring, a 14 gram Tungsten Hammer Weight, and four FX .35 cal. Sideshot Magazines (18 rounds each).
The retail price for the barrel kit from Utah Airguns is $400.00, the retail price of the magazines is $70.00 each, so for the four magazines it is $280.00, plus $30.00 for the Tungsten Hammer Weight, and $60.00 for the Huma High Flow Dual Hole Transfer Port. So the total retail for this tensioned slug barrel and the magazines and Tungsten Hammer Wt. & Huma Transfer Port would amount to $770.00. However, I am discounting that retail price by 20% due to the fact that they are used. So for everything listed above my price on this is $600.00...my price without the magazines is $400.00. This deal also includes free shipping anywhere in the CONUS.
As you will see from the photos below this barrel is already put together and ready to install on your Impact MKII or M3...you only have to remove the two front screws from your scope rail, remove the original barrel alignment block, install this barrel and reinstall the two screws through the new barrel clamping block and you are ready to rock and roll with some awsome NSA Slugs!
This barrel shoots the 93gr NSA slugs with amazing accuracy! Below is a photo of a target I shot at 100 yards on a breezy day and it shot that group just effortlessly! If you look real closely at the holes in the 100 yard target shown below, you will see that each of the holes are perfectly symetrical, which shows that the 93gr. slugs were totally stabilized all the way out to 100 yards! To achieve these results you must use slugs that measure .358 because this barrel likes them the best!
One caveat is that the barrel clamp has a small crack at the bottom either from too much recoil or me over tightening the screws, but these can be purchased from Utah Airguns very inexpensively. The barrel clamp that is now on the barrel has been on there since I first installed it, and has not affected the accuracy or performance in any way whatsoever, as you can see from the 100 yard target photo provided below.
And you can see from the photo of the magazines, I have modified the clear plastic covers so that for shooting slugs you can adjust your pin probe so that it protrudes into the mag well by 2mm, which allows the pin probe to push your slugs 2mm farther into the brass barrel inlet to a consistent depth. However, I will replace the modified plastic covers with unmodifed plastic covers if you prefer.
So if you have been thinking of getting a .35 cal. tensioned slug barrel to get into big game hog & deer hunting with some awesome hollow point NSA slugs, now is your chance to buy a ready to shoot set up and save $170.00 off the retail price! I will also make myself available if you need advice on how to tune your Impact rifle to achieve the 194 ft.lbs. of energy that I did with this set up.
I will accept payment by PayPal Friends/ Family.
All the best, Chuck Peffley
Here is the ad for this tensioned slug barrel kit from Utah Airguns, and also the ad for the FX Impact High Flow V2 Dual Hole Transfer Port Set, for reference: https://utahairguns.com/product/fx-impact-stx-slug-tensioned-barrel-kit/
huma-air.com
The retail price for the barrel kit from Utah Airguns is $400.00, the retail price of the magazines is $70.00 each, so for the four magazines it is $280.00, plus $30.00 for the Tungsten Hammer Weight, and $60.00 for the Huma High Flow Dual Hole Transfer Port. So the total retail for this tensioned slug barrel and the magazines and Tungsten Hammer Wt. & Huma Transfer Port would amount to $770.00. However, I am discounting that retail price by 20% due to the fact that they are used. So for everything listed above my price on this is $600.00...my price without the magazines is $400.00. This deal also includes free shipping anywhere in the CONUS.
As you will see from the photos below this barrel is already put together and ready to install on your Impact MKII or M3...you only have to remove the two front screws from your scope rail, remove the original barrel alignment block, install this barrel and reinstall the two screws through the new barrel clamping block and you are ready to rock and roll with some awsome NSA Slugs!
This barrel shoots the 93gr NSA slugs with amazing accuracy! Below is a photo of a target I shot at 100 yards on a breezy day and it shot that group just effortlessly! If you look real closely at the holes in the 100 yard target shown below, you will see that each of the holes are perfectly symetrical, which shows that the 93gr. slugs were totally stabilized all the way out to 100 yards! To achieve these results you must use slugs that measure .358 because this barrel likes them the best!
One caveat is that the barrel clamp has a small crack at the bottom either from too much recoil or me over tightening the screws, but these can be purchased from Utah Airguns very inexpensively. The barrel clamp that is now on the barrel has been on there since I first installed it, and has not affected the accuracy or performance in any way whatsoever, as you can see from the 100 yard target photo provided below.
And you can see from the photo of the magazines, I have modified the clear plastic covers so that for shooting slugs you can adjust your pin probe so that it protrudes into the mag well by 2mm, which allows the pin probe to push your slugs 2mm farther into the brass barrel inlet to a consistent depth. However, I will replace the modified plastic covers with unmodifed plastic covers if you prefer.
So if you have been thinking of getting a .35 cal. tensioned slug barrel to get into big game hog & deer hunting with some awesome hollow point NSA slugs, now is your chance to buy a ready to shoot set up and save $170.00 off the retail price! I will also make myself available if you need advice on how to tune your Impact rifle to achieve the 194 ft.lbs. of energy that I did with this set up.
I will accept payment by PayPal Friends/ Family.
All the best, Chuck Peffley
Here is the ad for this tensioned slug barrel kit from Utah Airguns, and also the ad for the FX Impact High Flow V2 Dual Hole Transfer Port Set, for reference: https://utahairguns.com/product/fx-impact-stx-slug-tensioned-barrel-kit/
FX Impact .35 High Flow V2 Dual Hole Transfer Port Set With Pin Probe
FX Impact .35 High Flow V2 Dual Hole Transfer Port Set With Pin Probe
huma-air.com 
