SPA P15 china bullpup

blazing! 10-20 shot count? Should be a really decent cheap pup. Most of the snowpeak stuff is really decent. 

Where can you get them. How about a spec sheet? 

Mrodair.com has them in .22 and .25, sounds like limited numbers in stock next week. 

"hcl"Hello :]
I bay one with .25 barrel.
At start shoot kings 1.645 with 220m/s of full power.
Mods :
Spread TP in barrel set reg. pressure to 150bar and give new spring Oteva 1.4mm 
and I have 3 mags (24 pellet) with 275m/s +-3m/s spread.

Bullpup is very light 2.2kg and short 68cm
With this power is very laud like 22lr so new silencer is needed :]
we test and mod it - topic on http://airgun-hunting.pl/viewtopic.php?f=3&t=8588

chrono with enlarged blasting chamber +30mm
two mags kings (and at the end 1 predator 1 barracuda hunter 1 barracuda) from 250bar to 150bar 

What do you mean "enlarged blasting chamber +30mm" ?

Click to expand...

I have one in 5.5mm, love the little guy, shoots really nice and accurate, I mod the internals of the shroud, the original baffles "sucks", took them off and made my own and made an adaptor with a 1/2"UNF male thread for an additional second stage silencer.

This looks like a nice platform to play, tinker and learn with at that price point. Is it regulated? Are there regulators available if not? Is that a self index mag? 

"intenseaty22"This looks like a nice platform to play, tinker and learn with at that price point. Is it regulated? Are there regulators available if not? Is that a self index mag?

Click to expand...

Yes, it is indeed, for the price tag, you get a nice little gun that is fun, light and accurate, easy to work on. It is regulated, also there are after market regulators for it, like the Huma and others, the mag is self indexing, not the best quality thou, could be better but does the job, but again, for the price, we can't ask for much!

Nice, thanks for the info. If / When I can get my hands on one, I will just fashion a single pellet loader. And these have a Titanium tank? What is max bar? 

It comes with 2 mags, and a single pellet loader, titanium cylinder, 250 bar max pressure

Impatiently waiting for the skyhawk release here in the states

Impatiently waiting for the skyhawk release here in the states

Click to expand...

My too in 177 caliber

UK, EU , China:
SMK Artemis P15 .177 or .22 PCP Bullpup Air Rifle

Click to expand...

http://www.gunstar.co.uk/smk-sportsmarketing-artemis-p15-25-air-rifles/Air-Guns/903434 SPA Artemis P15

• CALIBRE 4.5mm | 5.5mm | 6.35mm
• VELOCITY 4.5mm>900fps | 5.5mm:>800fps | 6.35mm>700fps (when tuned 900-920FPS - > 25,4gr .25)
• AIR CAPACITY 265CC <- titanium very light
• BULLET FIRING MODE Manual Running Fire
• CONSTANT VALVE Yes <- reg. pressure :]
• MAGAZINE CAPACITY 4.5(.177)11SHOTS | 5.5(.22) 9 SHOTS | 6.35(.25) 8 SHOTS
• TRIGGER PULL 1-5L bf
• MAXIMUM PRESSURE 250 bar
• HAMMER TEST 30 Lbsx30x (Safety ON)
• STOCK European BEECH
• L*W*H(MM) 675*200*40mm
• WEIGHT 2.0kg

[/QUOTE]

900-920fps with a 25gr .25 when tuned? We will see. I just dumped $450 into my P15 to try to achieve this. I had the added cost of a barrel because mine was only as accurate as a Walmart springer. Don't have the gun back from the machinist yet. We will see. I have so much money in this china gun that I call it my Chiapan.

Hi guys.

Just want to share my experience with my P15 in .22 calibre. I just fitted a Huma reg for a M10 on my P15 as the tube diametre on the P15 and M10 is the same. As you know, the M10 reg comes with a plenum. Measured this plenum volume at 13cc with a syringe and water. Shooting the JSB Beasts at around 820 fps. That is 50 fpe! I'm quite happy with that. I didn't need to do any porting at all. All I had to do is machine the lip on the valve housing where the old reg mounts so that the new plenum mounts flush onto a flat surface.

Did you screw the M10 reg at the P15 valve ?

Hi Mike. Sorry about the late reply. I was away. The M10 reg from Huma comes screwed onto a plenum when you purchase it. At the bottom of the plenum there is an O ring which runs along the outer circumference of it. When you unscrew the original reg out from the valve, you will see a lip on the edge of the valve which protrudes up. You need to machine this lip flat. Once this is done, just place the M10 reg(which is already screwed to a plenum) in the tube and screw the tube back onto the valve. The high pressure side will compress the M10 reg onto the flat surface of the valve and seal it against the valve. Its that simple. Get the reg and it will make better sense to you. Also, I have the reg set to 150bar and I have the option to go up to 170bar max! The standard P15 reg from Huma only goes to 150bar max.

Abdur, did you vent your M10 regulator by filing a groove in the threads and notching the tube? I only ask because unlike just screwing on the Huma P15 regulator and putting back together, the instructions for the M10 states that it needs to be vented when installed in an M10. I am not clear on whether venting is handled differently on the P15.

Hi PumaCarl.Yes I did file the threads on the valve housing and notch the tube as the regulator needs to be vented.I used a warding file to do this.Feel free to ask if you have any other questions.