Search results for query: *

I got a POI shift but accuracy was the same. and the POI shift was because the liner was removed and re-installed. When changing the transfer port, did you loosen the liner lock and pulled the liner out a tad? that will allow the transfer port to be properly seated. I only say it because that...

Hi guys, been some time since I have commented.... been busy with life :) I have the Huma duel and the FX power kit. My hammer weight is 7grams anyway so i didn't add the rings, Here are my findings.. Because I ported and modified the stock port and probe, the Huma kit did not give me any...

It looks like Edosan cut the M9 himself, but i could be wrong :)

The pellet probe length is the same, its just the back bit thats different. It will fit your probe holder without effecting pellet seating in barrel. 

Ahhh yours has a hole on side.... mine has none on side or top...must be a manufacturing fault... Better call Huma :(

Hmm no holes at all...

Hi guys, need some help with this. I received my Huma regulator for an FX Impact MKII with a 16mm Rod. Does it have a tiny hole where the red circle is ? mine does not, sorry about the picture i could not get a clearer one. 

https://www.airgunnation.com/topic/fps-jumps-up-what-can-be-the-cause/#post-631902 Centercut !! you are right.. I lubed the spring, hammer and rod thinking that it would be smooth. Will disassemble today and run some tests 

I tried that, I even left the gun and made me a cup of tea then took a shot...totally random for me sadly. But noticed if i turn the power wheel down to like setting 3 FPS will go down to 785 and it will keep a tight number. 

I have been trying to tune my .25 FX Impact today but noticed that 1 out of lets say 5 shots will be a much higher FPS for example. 902 910 905 912 923 <---- 905 904 909 930 <---- what would cause something like this? I do have a C3 delrin installed and I have checked it. This...

wow! now thats something I will do for sure! Love it !

Thank you for the input guys, I will verify with a scope cam tomorrow. What would be the clearest way to see it, shooting at a white wall for example with a reference dot or something?

OK.. today I wanted to verify that my scope is tracking true vertically. So I got a string with a weight on it and hung it over the target then marked a true line, placed a small 1inch by 1inch target at bottom. The picture attached shows how the scope was tracking going up 1Mil every shot. It...

Sorry, I made a mistake on first post and i fixed it, Its 0.25Mils which is 1/4 or 25% of a Mil Thanks for the links guys !! Machael, I printed that picture and pined it on my wall!

Thank you Michael, I have indexed the liner and I am planning to do it again to double check. Because I aligned it for the tightest group i could get, not for vertical POI. Out of interest, what distance is good to index. I did it at my zero distance of 30 meters 

Do you mean the scope is slightly twisted in its mounts or do you mean the barrel and scope are not aligned. Tomorrow I am planning to do a plumb line test by drawing a line on a long paper using a plumb line, then start shooting right at bottom of line, and dial in one Mil and shoot... i think...

Hi guys...need help understanding why I have to adjust windage the further my target is, and its not for wind.. so At 30m its dead on zero At 60m the hold over is spot on but hitting 0.25Mils to the left At 83m again hold over is spot on but hitting 0.5Mils to the left I can put pellet over...

Buy a springer guys, its easy 😆...but might need instructions on how to load a pellet.

The very best that I could do without hammer weight and plenum is 945fps and that is on (.25 - 700mm Slug liner Barrel - 34gr JSBs) Modified valve housing, ported TP and probe, Delrin C3 bumper. Hammer spring maxed out and regulator maxed till it dropped then backed up a bit. Like heavy said...

Very nice work! I will do that one day, but I understand that i must match the holes on the valve housing too. Best that i order a new valve block before haha cheers