Search results for query: *

I ordered some parts from them, specifically #19737 Impact shroud bushing, several weeks ago. This is the piece that screws into the backend of the shroud, This is what I told them when I ordered the parts along with photos: "I wanted to order two Impact shroud bushings #19737 but they appear...

SOLD for $265 on 10/03/2023 FX 580cc carbon fiber bottle 250 BAR is from my 2022 Impact M3. I'm selling the bottle because I had to switch to a 480cc bottle as I installed a Huma first stage regulator that extends out 1 1/4 inches more than the stock FX reg. As a result I could no longer screw...

FX .25 caliber magazine is brand new, never opened package. Extra magazine I intended to use with Maverick. This is the plastic magazine not the metal one. It should work with other top mount magazine FX rifles. Not compatible with the Impact. PayPal only, I'll pay the PayPal fee. Price: $45...

Bulletcentral had 5 in stock today.

This listing has been renewed

This listing has been renewed

This listing has been renewed

This listing has been renewed

I'm selling this Bullet Central tensioning kit for the FX Impact M3 700mm barrel. I decided to go back to my 600mm .22 setup so I no longer need the kit. Please note that if you have the FX barrel tensioning clamp installed, you will not be able to install the tensioning barrel as the clamp...

I have an FX M3 I bought last May 2022 and I have been dealing with a recent persistant leak issue. The gun is losing about 100 - 125 psi everyday, I've used leak detector spray all the known areas that could ne leaking, and I could not detect any bubbling or fizzing sounds. The one possible...

Thank you for finally thinking abiut us left handed shooters! I had to resort to using a single shot loader because the FX "right handed" mag stuck into my jawbone too much. All we need is now is a matching machined left handed cheek piece.

I didn't loosen the barrel block, but I decided to realign the scope rail ever so slightly. I loosened the front screw and the two rear screws, and shifted the back end of the scope rail to the right about half a milimeter. The front screw acting as a pivot point. That slight shift produced a...

I rotated (indexing) the sleeve to 3, 6, 9, 12 o'clock positions and that does effect the POI much like rotating barrel liner, I put a small mark on the tip of the carbon sleeve to see what position it is at while I rotated it. It is at the 3 o'clock position while the barrel liner is at the 9...

An unfortunate side effect of tensioning the carbon fiber sleeve is that my POI shifted more than 6 inches to the left on my .25 Impact M3. I was shooting at a distance of 57 yds. After I had finished indexing the STX heavy liner I purchased a few weeks back and got it zeroed in to my...

I'm trying make a slight angle adjustment on the trigger blade but I can't figure out what size hex key is used to remove the set screw. I know Fx lists the part as an M2x4 screw but not the key that fits into the screw head. I have tried my smallest hex heads on it, 1mm - too small, and 1.3mm -...

I've identified a leak coming out of the screw identified on the FX M3 schematic as D70 - Dog point grub screw M3x5. I don't see a rubber seal in the schematic so it appears to be just the screw sealing the hole. I've tried tightening it down but it is still is leaking. I don't want to tighten...

The spec-rest was discontinued by Lonestar Field Products a couple of years ago, most likely due to covid related production issues. If you have one laying around and in good/excellent condition and no longer need it, please contact me. Thanks

No date seen after removing the trigger guard. I removed the handle as well, but nothing under it.

I've looked at my newly purchased Impact and couldn't find a manufacture date printed/etched on it anywhere. Does any one know if its hidden somewhere on the gun? I've contacted FX USA, and Pyramyd Air where I purchased the gun from, and each one told me to ask the other company. Neither could...

Screw your air tube back in, and pressurize it back to 200 BAR. The added pressure pushing against the valve should lock it in place so you can unscrew the air tube and valve from the gun. Hatsan owner myself.